Business Community > All Threads > CPE510, Router/Client connectivity issue
< All Threads

CPE510, Router/Client connectivity issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

CPE510, Router/Client connectivity issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
CPE510, Router/Client connectivity issue
CPE510, Router/Client connectivity issue
2023-09-18 11:32:32 - last edited 2023-11-30 08:25:46
Tags: #Pharos Control #Repeater/Bridge Mode #Outdoor Wi-Fi Solution
Model: CPE510  
Hardware Version:
Firmware Version:

Hello Team,

 

We have installed CPE510, outdoor access point in our client site, we are repeatedly facing issue of connectivity. We have connected 2 CPE510 with each other as a router and client. For sometime everthing work well, but after sometime they use to get disconnect with each other. Then we have to Power off both antennas and restart them, then they will start working again, but after sometime they again gets disconnected.

 

Kindly help us with this issue, as we have multiple setup's like this, and all setup's are facing same issue. 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:CPE510, Router/Client connectivity issue-Solution
2023-09-19 02:38:51 - last edited 2023-11-30 08:25:46

  @Rajesh_Joshi 

 

Two CPEs do network extension point-to-point and have dropout problems, you need to go section by section to troubleshoot the possible causes.
You can first test whether this end of the AP CPE is working properly, if not, that means the problem may appear in the front end, you can change the network cable and check the router in the front end.


If the AP CPE is working, go to the CLient interface and check the Radio Status to see if it is properly connected to the AP CPE.

If it is properly connected, it is recommended to try different channels and channel widths on the AP CPE to see which one is more stable.

 

Check the firmware version, if it is not the latest one, you can upgrade it.


If this is no help, you will have to reset and reconfigure.
Also, make sure that the view between the two CPEs is clear.

Just striving to develop myself while helping others.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:CPE510, Router/Client connectivity issue-Solution
2023-09-19 02:38:51 - last edited 2023-11-30 08:25:46

  @Rajesh_Joshi 

 

Two CPEs do network extension point-to-point and have dropout problems, you need to go section by section to troubleshoot the possible causes.
You can first test whether this end of the AP CPE is working properly, if not, that means the problem may appear in the front end, you can change the network cable and check the router in the front end.


If the AP CPE is working, go to the CLient interface and check the Radio Status to see if it is properly connected to the AP CPE.

If it is properly connected, it is recommended to try different channels and channel widths on the AP CPE to see which one is more stable.

 

Check the firmware version, if it is not the latest one, you can upgrade it.


If this is no help, you will have to reset and reconfigure.
Also, make sure that the view between the two CPEs is clear.

Just striving to develop myself while helping others.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 491

Replies: 1

Tags

Pharos Control Repeater/Bridge Mode Outdoor Wi-Fi Solution
Related Articles
CPE510 point to point with CPE510 connection lost especially at night
677 0
Newb to tp-link CPE510
610 0
CPE510 Survey issue on repeater mode
843 0
Tp link Cpe 510 wireless multiple client
647 0
[SOLVED] PTMP Setup CPE510 - client remote management
678 0
Cpe510
81 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.