Business Community > All Threads > ER7206 Trunk Vlan with TL-SG108E
< All Threads

ER7206 Trunk Vlan with TL-SG108E

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER7206 Trunk Vlan with TL-SG108E

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER7206 Trunk Vlan with TL-SG108E
ER7206 Trunk Vlan with TL-SG108E
2023-05-11 17:17:03 - last edited 2023-05-15 02:36:53
Tags: #VLAN & Multi-Networks
Model: ER7206 (TL-ER7206)  
Hardware Version: V1
Firmware Version: 1.3.0 Build 20230322 Rel.70951

Hi - I have been building out a small network using a ER7206, a C2300 as an access point, and a TL-SG108E. I currently have the ER7206 and C2300 setup correctly with a separate VLAN on port 5. 

 

In attempting to stand up a VLAN Trunk (802.1Q) with TL-SG108E I've been hitting some road blocks. I want to use a single cable between the devices (an unfortunate hard requirement) but have VLAN segregation on the TL-SG108E with different IP Subnets.

 

For the configuration I have setup two LAN's, vlan20 and vlan30 with respective PVID's (20,30) on ER7206. Set them both as Tagged to port 4. I also setup two 802.1Q vlans on the TL-SG108E, vlan20 and vlan30 (PVID - 20,30) but no success.  Whatever the PVID is set to on the ER7206 is the subnet I receive for the specified ports downstream on the TL-SG108E. For instance if PVID 20 (vlan20) is specified, I can get an ip address from the LAN on ports 2-5. However, when attempting to get an IP address for vlan30 on Ports 6-8, my machine fails to receive an ip address from the ER7206 DHCP server. 

 

What should I do to correct my configuration? Is it even possible with the components?

 

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:ER7206 Trunk Vlan with TL-SG108E-Solution
2023-05-12 16:23:07 - last edited 2023-05-15 02:36:53

  @Virgo  - I found the issue. For future reference, the SG108E has to have the upstream port tagged in both VLAN's. Example:

 

690894f90e204924b8ae429040c3c147

Be sure to set the PVID's so the packets contain the correct info:

e31bae280a194b4bb99b61ed14cabfc9

 

Thanks for pointing me in the right direction!

Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:ER7206 Trunk Vlan with TL-SG108E
2023-05-12 07:18:22

  @dwahome 

 

Hi, first, you will need to configure the TL-SG108E switch to support VLAN tagging. This can be done by creating a VLAN ID for each of your VLANs and then tagging the appropriate ports with the VLAN ID. Next, you will need to configure the ER7206 router to support VLAN tagging as well. You will need to create a sub-interface for each VLAN and specify the VLAN ID for each sub-interface.

Once you have both devices configured for VLAN tagging, you can connect them using a single cable. The cable will need to be a trunk cable that supports 802.1Q tagging. You can then configure the trunk port on the TL-SG108E to allow both VLANs to pass through the port.

Finally, you will need to configure your access point to support VLAN tagging as well. You will need to create a separate SSID for each VLAN and specify the VLAN ID for each SSID. This will allow clients to connect to the appropriate VLAN based on the SSID they connect to.

 

And check this: How to configure 802.1Q VLAN

Just striving to develop myself while helping others.
  0  
  0  
#2
Options
Re:ER7206 Trunk Vlan with TL-SG108E
2023-05-12 13:47:56 - last edited 2023-05-12 16:15:28

  @Virgo 

 

Thanks very much for the pointers. There is a specific cable that I need to use? Crossover? Simple Patch cable? Currently using a Cat5e patch for testing purposes but a Cat6 patch is installed on site.

 

I will reset everything and attempt your walkthrough. When setting up the sub-interfaces I'm assuming I can add a DHCP server on each?

 

EDIT: I added all of my LAN's with appropriate subnets on the ER7206

3403bc2358f14fbab877884405f3915d

I then added the Tagged flag on the two VLAN's that should be trunked on a single port.

7988a2015acc492182f5931455867d91

As you can see, I want them to trunk on Port 4. Vlan 10 is a separate subnet that doesn't require tagging. I then setup the SG108E with the same VLAN information:

91ea663b51fc49e282cfcd197ff86caf

However, the only VLAN that works correctly is vlan20 which happens to be the PVID for port 4 on the ER7206:7876b82623834dceafaf07f8d1ff4a05

 

Am I missing something for either appliance?
 

  0  
  0  
#3
Options
Re:ER7206 Trunk Vlan with TL-SG108E-Solution
2023-05-12 16:23:07 - last edited 2023-05-15 02:36:53

  @Virgo  - I found the issue. For future reference, the SG108E has to have the upstream port tagged in both VLAN's. Example:

 

690894f90e204924b8ae429040c3c147

Be sure to set the PVID's so the packets contain the correct info:

e31bae280a194b4bb99b61ed14cabfc9

 

Thanks for pointing me in the right direction!

Recommended Solution
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 1961

Replies: 3

Tags

VLAN & Multi-Networks
Related Articles
TL-ER7206 Maximum VLAN and DHCP POOL
1253 0
ER7206 dns setup for ms win network discovery & multi vlan
804 0
er7206 vlan without a switch
1690 0
ER7206 - layer 2 VLAN
425 0
Inter-VLAN communications - ER7206 - SG2218 - EAP218
145 0
TL-ER7206 - Two WAN PPPOE connections on same VLAN ID error
1405 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.