vlan
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Buenas Tardes, mi pregunta es sobre las vlan. por ejemplo tengo este switch t1600g-28ps y estoy usando el puerto 1 y 8
en el 8 va hacia un router principal
en el 1 va a switch donde exite dos router de repetidor, este switch no es programable, ya que me fue imposible cablear hasta el switch t1600g-28ps dos cable UTP.
mi pregunta es:
es posible ponerle dos vlan en el mismo puerto 1 del switch principal (troncal), para que sea una vlan para un router y otra vlan para el otro router?
si fuera esto cierto, como pondria los Untagged Ports o tagged Ports correspondeinte y su PVID si solo sale por el puerto 1 del switch t1600g-28ps hacia los dos router?
muchas gracias
Good afternoon, my question is about vlans. for example i have this switch t1600g-28ps and i am using port 1 and 8 in 8 it goes to a main router 1 goes to the switch where there are two repeater routers, this switch is not programmable, since it was impossible for me to wire two UTP cables to the t1600g-28ps switch. my question is: Is it possible to program two vlans on the same port 1 of the main (trunk) switch, so that it is one vlan for one router and another vlan for the other router? If this were true, how would I put the corresponding Untagged Ports or Tagged Ports and their PVID if it only goes out through port 1 of the t1600g-28ps switch to the two routers? Thanks in advance
Buenas y perdona por el dibujo, no estoy en cas y lo hice rapido, te entiendo lo que comentas, los repetidores son dos router Netis donde conecto en la wan una ip estatica del mismo rango correspondiente, ya sea VLAN o solo la lan del router principal. la idea es ir cambiando los netis y poner router tplink cuando pueda.
Por otro lado te entiendo lo que me comentas. seria hacer las vlan en el tl-r605 y dejar el tl-sg3210 solo access es decir como viene de fabrica y etiquetado en el router tl-r 605?
lo voy a ejecutar y te iré diciendo. muchas gracias a todos.
Good morning and sorry for the drawing, I'm not at home and I did it quickly, I understand what you're saying, the repeaters are two Netis routers where I connect a static ip of the same corresponding range to the wan, either VLAN or just the lan of the router major. The idea is to change the netis and put tplink router when possible. On the other hand, I understand what you are saying. Would it be to make the vlans in the tl-r605 and leave the tl-sg3210 only access, that is, how it comes from the factory and labeled in the tl-r 605 router? I'm going to execute it and I'll tell you. thank you very much to all.
ER605 will support VLAN on its WAN interface if you want to replace NETIS with TPLink routers.
You could also replace the unmanaged switch with a managed switch and use the primary ER605 to do ALL the DHCP and routing downstream just by appropriately configure the switch on the second floor
Keen to hear how your test works out!
- ok ya estoy entendiendo mas tl-er605 y lo que estas diciendo
-
ok I am understanding more tl-er605 and what you are commenting
- Puedo crear las vlan y la red en el router principal tl-er605 como se ve en la captura
-
I can create the vlans and the network on the main router tl-er605 as seen in the screenshot
- La salida de ese puerto lo pongo etiquetado hacia la entrada 8 del switch tl-sg3210
-
I label output 5 of that port to input 8 of the tl-sg3210 switch
- este es el switch tl-sg3210
- this is switch tl-sg3210
- y el switch tl-sg3210 lo dejo como esta ya que a los router repetidor les pondria la ip correspondiete estaticamente a la vlan 101 y 102
-
and the switch tl-sg3210 I leave it as it is since I would put the ip statically corresponding to the repeater routers to vlan 101 and 102