Business Community > All Threads > Replacing an OC200 Controller v1 with a V3 and using a backup to restore
< All Threads

Replacing an OC200 Controller v1 with a V3 and using a backup to restore

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Replacing an OC200 Controller v1 with a V3 and using a backup to restore

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Replacing an OC200 Controller v1 with a V3 and using a backup to restore
Replacing an OC200 Controller v1 with a V3 and using a backup to restore
2022-09-04 13:44:52 - last edited 2022-09-04 16:09:59
Model: OC200  
Hardware Version: V1
Firmware Version: 5.5.7

I believe I may have to replace my existing OC200 (See that discussion here.)

 

Anyway, my current OC200 is a V1.  If I have to replace it, and I get the current V3 version, will I be able to use a backup from my current V1 to apply all of its settings to the new V3?  In other words, does the backup contain just the OC200's settings or does it include the firmware too - which would be the V1 version and not compatible with the new V3 OC200.

 

TIA

(1) TL-R605 v1.0 Router/Gateway (1) OC200 v1.0 Controller (1) TL-SG2210P v3.20 POE Switch (2) TL-SG2218 v1.0 POE Switch (3) EAP245 v3.0 Access Point (1) EAP225-Outdoor v1.0 Access Point
  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Replacing an OC200 Controller v1 with a V3 and using a backup to restore-Solution
2022-09-04 15:00:35 - last edited 2022-09-04 16:09:59

  @lflorack 

 

The backup is only the configuration of the OC200, it wont contain the firmware.

 

You need to ensure the new OC200 is on the same firmware (or close too anyways) as your backup.  However this usually works fine :)

 

The only real difference is the hardware inside, with the ongoing chip shortage TP Link appears to have had to change the internal chipset to accommodate supply and this increments the version numbers, however, they are fundamentally the same device overall

Recommended Solution
  2  
  2  
#2
Options
2 Reply
Re:Replacing an OC200 Controller v1 with a V3 and using a backup to restore-Solution
2022-09-04 15:00:35 - last edited 2022-09-04 16:09:59

  @lflorack 

 

The backup is only the configuration of the OC200, it wont contain the firmware.

 

You need to ensure the new OC200 is on the same firmware (or close too anyways) as your backup.  However this usually works fine :)

 

The only real difference is the hardware inside, with the ongoing chip shortage TP Link appears to have had to change the internal chipset to accommodate supply and this increments the version numbers, however, they are fundamentally the same device overall

Recommended Solution
  2  
  2  
#2
Options
Re:Replacing an OC200 Controller v1 with a V3 and using a backup to restore
2022-09-04 16:11:32

  @Philbert 

Thank you very much! 

That will make my transition to a replacement OC200 if my current OC200 ends up being my issue.

(1) TL-R605 v1.0 Router/Gateway (1) OC200 v1.0 Controller (1) TL-SG2210P v3.20 POE Switch (2) TL-SG2218 v1.0 POE Switch (3) EAP245 v3.0 Access Point (1) EAP225-Outdoor v1.0 Access Point
  0  
  0  
#3
Options

Information

Helpful: 0

Views: 789

Replies: 2

Related Articles
Oc200 V1 compatibility
310 0
oc200 v1 Dpi Help
1022 0
OC200 Controller Migration to Software Controller Error
748 0
AutoBackup on OC200 controller not enabled
1442 0
OC200 vs Software Controller
5947 0
OC200 Controller Compatibility with EAP650
281 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.