Business Community > All Threads > TL-R605 to CenturyLink LCP timeout
< All Threads

TL-R605 to CenturyLink LCP timeout

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-R605 to CenturyLink LCP timeout

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-R605 to CenturyLink LCP timeout
TL-R605 to CenturyLink LCP timeout
2021-10-24 20:02:56
Model: ER605 (TL-R605)  
Hardware Version: V1
Firmware Version: 1.1.1

Trying to connect a tp-link TL-R605 router to a century link ActionTech C3000.

 

Followed Century Link suggestions: physical connection between WAN port on TL-R605 to

a non-wan port on the ActionTech. Set the ActionTech to Transparent Bridging with tagged-201 VLAN.

 

Set the tp-link to connect via PPPoE (as the ActionTech was configured) along with the

appropriate name and password. Also, set to use VLAN 201.

 

Connection fails. Log shows:

 

   PPPoE Discovery phase negotiation succeeded

   LCP sending CONFIG-REQUEST timeout

 

My incoming network is a bonded DSL pair which goes to the ActionTech DSL

phone input. As I understand it, the WAN ethernet port on this device is not used

unless one has gigabit CenturyLink.

  0      
 
  0      
 
#1
Options
5 Reply
Re:TL-R605 to CenturyLink LCP timeout
2021-10-25 09:24:56

@DQP 

 

I'm a bit confused as to how you managed to set the DSL modem to bridge mode and also set the Vlan on it？

Actually you can try using the modem router as router mode to see if you can get an IP properly after you use the PPPOE.

Just striving to develop myself while helping others.
  0  
  0  
#2
Options
Re:TL-R605 to CenturyLink LCP timeout
2021-10-25 15:58:09

@Virgo The actiontech C3000A has several WAN settings including this passthrough mode. There is also an additional tagged-201 option that was suggested by CenturyLink. When this modem is set to PPPoE, it connects properly. I don't have an option of connecting the TP-Link directly since I have incoming bonded pair phone lines and that only connects to the actiontech modem.

  0  
  0  
#3
Options
Re:TL-R605 to CenturyLink LCP timeout
2021-10-26 02:26:58

@DQP 

 

You can also think differently, e.g. set up PPPoE + VLAN on the modem router to work normally as a router,

and select dynamic IP as the network connection type for the ER605.

You may have a try.

Just striving to develop myself while helping others.
  0  
  0  
#4
Options
Re:TL-R605 to CenturyLink LCP timeout
2021-10-26 03:00:15
The TP-Link can use dynamic IP for its WAN connection, but it doesn't allow this to be the same network as the LAN. Doesn't it need both connections to operate properly?
  0  
  0  
#5
Options
Re:TL-R605 to CenturyLink LCP timeout
2021-10-27 03:58:22
Thinking about this some more ... perhaps I can set the WAN address to just a fixed one on the regular LAN and then create a new LAN on the other side of this device for VPN access....
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1460

Replies: 5

Related Articles
TL-R605 IPv6
1692 3
TL-R605 Performance
7771 1
Deploying the TL-R605...
975 0
ER7206 - LCP sending ECHO-Request Timeout
1244 0
TL-R605 WAN Setup
2507 0
Differences between TL-R605 and ER605
15094 2
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.