Home

Forums

Stories

Knowledge Base

Business Community > All Threads > Eap245 will not connect when enabled management vlan

< All Threads

Eap245 will not connect when enabled management vlan

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Eap245 will not connect when enabled management vlan

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Toppy

2021-04-12 16:18:19 - last edited 2021-04-22 02:16:16

Posts: 8

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-04-07

Eap245 will not connect when enabled management vlan

2021-04-12 16:18:19 - last edited 2021-04-22 02:16:16

Model: EAP245

Hardware Version: V3

Firmware Version: 5.0.1

Hi,

Using a OC200 controller with a TL-R605 & TL-SG2210MP hardware.

When adopt the EAP245 it will connect in the controller software.

Port 8 is connected to the OC200, Port Lan of the TL-R605 is connected to port 1 of the switch and port 2 is connected to the eap245.

Profile all is selected on all ports of the switch, when open the eap245 and go's to config > services and enable management vlan the eap245 will be configuring and after a minute or so adopting and then the connection shows a default ip address (fallback) and it stays on adopting.

What do i miss here,

Thanks in advance.

1 Accepted Solution

Toppy

LV1

2021-04-21 12:43:00 - last edited 2021-04-22 02:16:16

Posts: 8

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-04-07

Re:Eap245 will not connect when enabled management vlan-Solution

2021-04-21 12:43:00 - last edited 2021-04-22 02:16:16

@Toppy

If i follow those steps " Network with an Omada Managed Router as the Gateway" I only using a local OC200 (no cloud connection) the devices (Switch and a AP) are getting the disconnected status in Devices menu.

Not sure what i do wrong.

Regards,

Looks like https://community.tp-link.com/en/business/forum/topic/232786

Recommended Solution

3 Reply

Fae

2021-04-19 09:30:52 - last edited 2021-04-22 02:16:16

Posts: 3604

Helpful: 1360

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:Eap245 will not connect when enabled management vlan

2021-04-19 09:30:52 - last edited 2021-04-22 02:16:16

Dear @Toppy,

Toppy wrote

Port 8 is connected to the OC200, Port Lan of the TL-R605 is connected to port 1 of the switch and port 2 is connected to the eap245.

Profile all is selected on all ports of the switch, when open the eap245 and go's to config > services and enable management vlan the eap245 will be configuring and after a minute or so adopting and then the connection shows a default ip address (fallback) and it stays on adopting.

The OC200 controller cannot handle tagged packets, you may create a profile for port 8 that is going to the controller.

Here is a Management VLAN configuration guide for your reference, How to configure Management VLAN in Omada SDN Controller

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Toppy

LV1

2021-04-19 10:57:30 - last edited 2021-04-22 02:16:16

Posts: 8

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-04-07

Re:Eap245 will not connect when enabled management vlan

2021-04-19 10:57:30 - last edited 2021-04-22 02:16:16

@Fae

Thanks i will try and test it again, i had follow the configuration in the link you send me.

Regards,

Toppy

LV1

2021-04-21 12:43:00 - last edited 2021-04-22 02:16:16

Posts: 8

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-04-07

Re:Eap245 will not connect when enabled management vlan-Solution

2021-04-21 12:43:00 - last edited 2021-04-22 02:16:16

@Toppy

Not sure what i do wrong.

Regards,

Looks like https://community.tp-link.com/en/business/forum/topic/232786

Information

Helpful: 0

Replies: 3

Eap245 will not connect when enabled management vlan

Eap245 will not connect when enabled management vlan

Information

Voters 0

Tags