Business Community > All Threads > CPE710 - how to optimize
< All Threads

CPE710 - how to optimize

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

CPE710 - how to optimize

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
CPE710 - how to optimize
CPE710 - how to optimize
2020-11-16 16:58:01 - last edited 2020-11-18 15:36:37

I wanted to ask if anyone could recommend how to optimize and get the most out of the following set up using the CPE710.   I have a server in a barn about 600ft away with clear line of site.   I saw that the CPE710 can do about 800MB/s so I purcahsed one.   No I want to optimize this connection and share the server across my network at my house in the most efficient manner (less cost the better).   Do I need another CPE710 at the barn so the two can connect as a point to point in order to get the max speed.   If that is the case then should I set the CPE710 up as an AP, client point to point, bridge?   Should the CPE710 at the barn go to a router there or just to a switch to extend the network and then add sepaprate APs like the outdoor AC1200?   

 

Any ideas or equipment connection advice would be very much appreciated!

 

Thanks!

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:CPE710 - how to optimize-Solution
2020-11-18 07:17:50 - last edited 2020-11-18 15:36:37

Dear @BSOD47,

 

Do I need another CPE710 at the barn so the two can connect as a point to point in order to get the max speed. If that is the case then should I set the CPE710 up as an AP, client point to point, bridge? 

 

It's suggested to use two of CPE710 to build up a point to point wireless connection. The typical setup is like this:

main router ---- 1st CPE710 in AP mode )))((( 2nd CPE710 in Client mode ---- devices

 

Here is an example for your reference. https://www.tp-link.com/support/faq/1226/

 

Should the CPE710 at the barn go to a router there or just to a switch to extend the network and then add sepaprate APs like the outdoor AC1200?   

 

It's up to your demands. If you need to extend the network outdoor and connect with several wired devices including the outdoor AP, then connect the CPE710 Client to a switch and add the other wired devices.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options
4 Reply
Re:CPE710 - how to optimize-Solution
2020-11-18 07:17:50 - last edited 2020-11-18 15:36:37

Dear @BSOD47,

 

Do I need another CPE710 at the barn so the two can connect as a point to point in order to get the max speed. If that is the case then should I set the CPE710 up as an AP, client point to point, bridge? 

 

It's suggested to use two of CPE710 to build up a point to point wireless connection. The typical setup is like this:

main router ---- 1st CPE710 in AP mode )))((( 2nd CPE710 in Client mode ---- devices

 

Here is an example for your reference. https://www.tp-link.com/support/faq/1226/

 

Should the CPE710 at the barn go to a router there or just to a switch to extend the network and then add sepaprate APs like the outdoor AC1200?   

 

It's up to your demands. If you need to extend the network outdoor and connect with several wired devices including the outdoor AP, then connect the CPE710 Client to a switch and add the other wired devices.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options
Re:CPE710 - how to optimize
2020-11-18 15:36:17

@Fae 

 

This is perfect and the example is spot on!  Thanks so much!

  0  
  0  
#3
Options
Re:CPE710 - how to optimize
2020-11-18 15:36:18

@Fae 

 

This is perfect and the example is spot on!  Thanks so much!

  0  
  0  
#4
Options
Re:CPE710 - how to optimize
2020-11-19 02:36:35

Dear @BSOD47,

 

This is perfect and the example is spot on!  Thanks so much!

 

Welcome and thank you for your feedback on the example. Hope you could enjoy the Internet with TP-Link products!

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1984

Replies: 4

Related Articles
Cpe710
508 0
CPE710 VLANs
6387 0
Pharos CPE710
570 0
CPE710 Firmware
1256 0
CPE710
973 0
CPE710
1461 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.