Business Community > All Threads > How to set up a TL-ER5120 Router before a Deco M4 mesh network to have load balancing
< All Threads

How to set up a TL-ER5120 Router before a Deco M4 mesh network to have load balancing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to set up a TL-ER5120 Router before a Deco M4 mesh network to have load balancing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to set up a TL-ER5120 Router before a Deco M4 mesh network to have load balancing
How to set up a TL-ER5120 Router before a Deco M4 mesh network to have load balancing
2020-07-09 02:45:09 - last edited 2021-04-19 10:56:58
Model: TL-ER5120  
Hardware Version: V4
Firmware Version:

I have a Deco M4 Network. router+6 APs (5 wired, 2 wifi), few switches.. 300MB bandwith from 1 ISP - working perfectly

Just added a 2nd ISP (also 300mb) and bought a TL-ER5120 in order to have load balancing and backup if 1 ISP is down

What's the best way to add the ER5120 in order to have?

- load balance
- eventually add both bandwiths
- to have the network running even if 1 ISP is down
- keep the mesh wifi setup
 

Should I add the ER5120 as main router and all deco M4s as access points? would this keep MESH?

Should I add the ER5120 in bridge mode and keep one Deco M4 as main? (Is this possible to use the ER5120 in bridge mode while balancing loads and adding bandwiths?

  0      
 
  0      
 
#1
Options
1 Reply
Re:How to set up a TL-ER5120 Router before a Deco M4 mesh network to have load balancing
2020-07-10 07:23:12 - last edited 2021-04-19 10:56:58

@DADArg 

 

Hi,

 

It is suggested to use the ER5120 as the main router, the setup could be ER5120 ----Deco M4 )))((( RE Deco1, 2, 3...

 

As for the Deco M4, you could keep one Deco M4 as main,  Ethernet Backhaul feature on Deco

or you could also set all of them as access points, which would also keep MESH.

 

I have a Deco M4 Network. router+6 APs (5 wired, 2 wifi), few switches.. 300MB bandwith from 1 ISP - working perfectly

Just added a 2nd ISP (also 300mb) and bought a TL-ER5120 in order to have load balancing and backup if 1 ISP is down

What's the best way to add the ER5120 in order to have?

- load balance
- eventually add both bandwiths
- to have the network running even if 1 ISP is down
- keep the mesh wifi setup
 

Should I add the ER5120 as main router and all deco M4s as access points? would this keep MESH?

Should I add the ER5120 in bridge mode and keep one Deco M4 as main? (Is this possible to use the ER5120 in bridge mode while balancing loads and adding bandwiths?

 

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 837

Replies: 1

Related Articles
er5120 router cannot access
470 0
/31 IP Subnet on TL-ER5120
1251 0
TL-ER5120 mac filter entries limit
597 0
TL-ER5120 Multi Public IP addresses
1943 0
Router tl-er5120 Max clients allowed
1032 0
TL-ER5120 and VOIP
1456 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.