Connecting WBS-510 with dish as client to WBS-510 with sector.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Connecting WBS-510 with dish as client to WBS-510 with sector.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Connecting WBS-510 with dish as client to WBS-510 with sector.
Connecting WBS-510 with dish as client to WBS-510 with sector.
2019-10-22 14:33:21 - last edited 2019-10-22 14:35:11
Model: WBS510  
Hardware Version:
Firmware Version:

Hi guys, 

I'm working on a video surveillance project, the site is 2km away from HQ. Both in rural area site is at higher level than HQ, there are trees but I am hoping to get LOS with high masts. 

Since the site will be constantly uploading about 100mbits ps I am trying to connect wbs510 client with dish pointed at wbs510 ap with sector antenna TL-ANT5819MS. 

What you guys think about this configuration? 

I have cpe610 and cpe510 available too. But my concern is trees, they grow.. 

Thanks. 

  0      
  0      
#1
Options
5 Reply
Re:Connecting WBS-510 with dish as client to WBS-510 with sector.
2019-10-23 01:18:06

 

Aliturkmen wrote

Since the site will be constantly uploading about 100mbits ps I am trying to connect wbs510 client with dish pointed at wbs510 ap with sector antenna TL-ANT5819MS. 

What you guys think about this configuration? 

 

Why would you consider to use a sector antenna? If you want to achieve a constant 100 Mbps (data) throughput you will need a PtP link anyway, so the WBS510 AP should have a dish also (e.g. TL-ANT5830, designed for WBS510). I have no experience with CPE610 yet, but I would prefer two WBS510 with TL-ANT5830 anyway.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#2
Options
Re:Connecting WBS-510 with dish as client to WBS-510 with sector.
2019-10-23 01:24:47 - last edited 2019-10-23 01:27:11

@R1D2 thanks a lot for the reply. 

I am preferring sector antenna because there are two more existing cameras both uploading from cpe510s to cpe510 ap. I was thinking to upgrade the ap to WBS510 with sector. So three sites in total within about 60 degrees. The actual upload rate won't reach 100mbits. There are 4 or 5 cams 1080p 6-8 fps. 

  0  
  0  
#3
Options
Re:Connecting WBS-510 with dish as client to WBS-510 with sector.
2019-10-23 01:36:11

Aliturkmen, I think you should give it a try. But keep in mind that the wider the antenna beam width (90º/120º for sector antenna compared to 6º for the dish antenna), the weaker the RF energy, so a fresnel zone clearance is of the utmost importance.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#4
Options
Re:Connecting WBS-510 with dish as client to WBS-510 with sector.
2019-10-23 01:42:26

@R1D2 indeed fresnel zone is what I am afraid of most here because Los is hardly available already because of trees. Maybe I should just wire one WBS-510 ap with dish specially for this new site to the mast, leaving the existing setup separate.

Thanks.

  0  
  0  
#5
Options
Re:Connecting WBS-510 with dish as client to WBS-510 with sector.
2019-10-23 02:31:42 - last edited 2019-10-23 02:32:18

Yes, trees and even rain have an effect on the radio link and at a distance of 2km this could become a problem. But I would try it anyway. Surprisingly, for me it did work over 600m distance in practice better than predicted in theory, see this story here.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1091

Replies: 5

Related Articles