Business Community > Pharos Wireless Bridges > CPE520 AP installation
< Pharos Wireless Bridges

CPE520 AP installation

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

CPE520 AP installation

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
CPE520 AP installation
CPE520 AP installation
2016-10-10 18:46:16
Model :

Hardware Version :

Firmware Version :

ISP :





ISP : 2 AP (510 and 520) connected to fiberline with 100mbps internet download and upload speed (ookla). its modem was set to dhcp

AP1 CPE510 throws to Client CPE510 with 90mbps speedtest (ookla) (transmit cqq:90)

AP2 CPE520 throws to client CPE520 for just 0.20mbps... (transmit cqq:78)

with the same settings and configuration for 510's and 520's, why am getting only 0.20mbps?

why am getting a 0.20mbps reading?

my settings for Client2 Transmit CQQ is 80
  0      
 
  0      
 
#1
Options
17 Reply
Re:CPE520 AP installation
2016-10-11 08:56:15
could you share the status screenshot of the CPE520? I assume you have bad alignment
  0  
  0  
#2
Options
Re:CPE520 AP installation
2016-10-11 10:20:56
attached screenshot 520ap
File:
Screenshot_20161011-101551.jpgDownload
  0  
  0  
#3
Options
Re:CPE520 AP installation
2016-10-11 10:33:37
[attach=config]4262[/attach]

520 ap
File:
  0  
  0  
#4
Options
Re:CPE520 AP installation
2016-10-11 10:52:52
Client2 502

Tx/Rx: 15mbps?



  0  
  0  
#5
Options
Re:CPE520 AP installation
2016-10-11 20:36:42
@Tonting, answer this, where the backhaul is AP-1 & AP-2
1-Both connected by its POE, or using one POE, and POE passthrough to the second one
2-what's the separation between APs, minimum 3 meters
3-what channel is set on AP-1, on AP-2 is 157
  0  
  0  
#6
Options
Re:CPE520 AP installation
2016-10-11 22:40:36
ive just disabled AP2(unpluged poe)and turn AP1(510) around and point it to Client2(520)...same speed.. well it increased 0.5mbps..also i installed Pharos Control software, and it can detect and manage all CPEs... something wrong with the 520's?
  0  
  0  
#7
Options
Re:CPE520 AP installation
2016-10-12 08:44:52
the signal strength is too weak, try to install devices as tall as possible, and avoid the ostacles. Is the AP and client face-to-face?
Signal stength less than -75dBm is considered very weak.
  0  
  0  
#8
Options
Re:CPE520 AP installation
2016-10-12 12:22:56
with the same location , a week ago, AP2 and Client2 were both cpe510 and connected to isp 50mbps.. getting 5mbps ookla speed

i tought upgrading to both cpe520 and 100mbps isp will increase and improve signal and speed,,, but unfortunately.. getting .5mbps speed..
  0  
  0  
#9
Options
Re:CPE520 AP installation
2016-10-12 12:24:38

YXCY wrote

the signal strength is too weak, try to install devices as tall as possible, and avoid the ostacles. Is the AP and client face-to-face?
Signal stength less than -75dBm is considered very weak.


i guess interferance probably the issue...
  0  
  0  
#10
Options
Re:CPE520 AP installation
2016-10-12 13:12:34




i have an 85% sight in the building where my Client is located..
  0  
  0  
#11
Options
12

Information

Helpful: 0

Views: 3195

Replies: 17

Related Articles
 Pairing a CPE520 with CPE610
906 0
 CPE520 power consumption
724 0
 What are the sensitivity values in the CPE520 receiver
424 0
 CPE520 Setup Signal Strength
1943 0
 CPE520 don´t have "PoE Passthrough" option
1117 0
Installation help
385 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.