Business Community > Pharos Wireless Bridges > CPE210 Transmit Power Calculations?
< Pharos Wireless Bridges

CPE210 Transmit Power Calculations?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

CPE210 Transmit Power Calculations?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
CPE210 Transmit Power Calculations?
CPE210 Transmit Power Calculations?
2016-09-24 10:17:42
Model :

Hardware Version :

Firmware Version :

ISP :

Wondering if there is a way to calculate what the Transmit Power should be based on distance for a CPE210.

I setup 2 CPE210's for a client a while ago, it is fairly short range (200 ft, or ~60m). They contacted me & say their speed vary's quite a bit with as much as a 50% loss in throughput between the devices (tested using speedtest.net). After a bit of research, I am almost certain that I have the transmit power set too high (left on the default 27dBm). There are only a few other APs on different channels nearby, so I don't think it's an interference issue (I could be wrong though).

Is there anyway to calculate optimal transmit power or is it more of a trial & error thing.

Would love to get some input on this before heading out there again next week.


Thanks
  0      
 
  0      
 
#1
Options
6 Reply
Re:CPE210 Transmit Power Calculations?
2016-09-24 12:31:11
if if only for 60 Mts you should set the power of the equipment at maximum 13dBm on both devices to get the best signal levels in signal strength and SNR ... remember that the values ​​of signal strength values ​​are shown in negative and the closer to zero will be the best and CCQ while levels closer to 100% will also be better ... for more understanding of what I say should refer to this link to the knowledge base specifically point 4. Precise alignment ... http://forum.tp-link.com/showthread.php?86640-Filed-Test-Remote-Wireless-Surveillance-with-Pharos-CPE510

Regards...
  0  
  0  
#2
Options
Re:CPE210 Transmit Power Calculations?
2016-09-25 12:31:45

Victor Ramos wrote

if if only for 60 Mts you should set the power of the equipment at maximum 13dBm on both devices to get the best signal levels in signal strength and SNR ... remember that the values ​​of signal strength values ​​are shown in negative and the closer to zero will be the best and CCQ while levels closer to 100% will also be better ... for more understanding of what I say should refer to this link to the knowledge base specifically point 4. Precise alignment ... http://forum.tp-link.com/showthread.php?86640-Filed-Test-Remote-Wireless-Surveillance-with-Pharos-CPE510

Regards...


Thanks for that info! That will give me a good starting point for troubleshooting when I'm on-site next week.

Much appreciated! :)
  0  
  0  
#3
Options
CPE210 Transmit Power Calculat
2016-10-01 09:16:24
Can anyone pls clarify the maximum Transmit power of SXT 2?As per specs the chip has 32dbm max transmit power and the antenna is 10dbi. So the total max transmit power out of the antenna is 42db=15.85watts?Am I correct?
  0  
  0  
#4
Options
Re:CPE210 Transmit Power Calculations?
2016-10-01 10:45:34
Im sorry STX2 is MikroTik brand ... Wrong forum....

Technically how to obtain the total EIRP is the same in any radius ...

Regards...
  0  
  0  
#5
Options
CPE210 Transmit Power Calculations
2016-11-15 11:26:16
well it says at full burn it can supply 2W of constant power. Watts is volts time amps, so 2W at 5vstandard USB woudl be 0.4Amps or 400 milliamps. I think a PC power usb port is 500 milliamps, so it should charge a USB gadget at about the same rate as charging from a PC.
  0  
  0  
#7
Options
Re:CPE210 Transmit Power Calculations?
2016-11-15 19:02:06

Dendiger43 wrote

So the total max transmit power out of the antenna is 42db=15.85watts?Am I correct?


Yes, that's correct. See http://www.rapidtables.com/convert/power/dBm_to_Watt.htm for a converter from dBm to Watts.

But regulations won't allow such a high EIRP, be careful to not exceed the maximum allowed EIRP in your country!
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#8
Options

Information

Helpful: 0

Views: 3142

Replies: 6

Related Articles
Transmit power
421 0
CPE210 V3 CPE Outdoor Power Transmit Legacy
140 0
 CPE210 does not transmit wlan
251 0
CPE710 Disconnection and weak transmit power
737 0
Can you power a CPE210 with 12VDC PoE?
1490 0
 Transmit Power of CPE 220
1237 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.