R600VPN Config

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

R600VPN Config

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
R600VPN Config
R600VPN Config
2015-11-02 15:40:39 - last edited 2021-08-21 05:28:00
Model :

Hardware Version : Not Clear

Firmware Version :

ISP :

I have a pair of R600VPN routers. I have connectivity between the 2 units via the WAN interface via the IPSEC tunnel ( as verified via the traceroute - no intermediate link). I want to route all treffic from one VPN router to the other VPN router, to be routed to a separate internet connection. All traffic via site 'B' will royter via site 'A' and then default route to the Internet via site 'A'. I want to understand how the default routes and static routes need to be configured to achieve this.

Site 'A'
Local subnet 192.168.1.0/24
Default router 192.168.1.1 (route to the Internet router)
Local LAN VPN router LAN address 192.168.1.2
WAN - 1.1.1.1

Site 'B'
Local subnet 192.168.2.0/24
local LAN VPN router LAN address 192.168.2.1
WAN 2.2.2.2

Hopefully someone can point me in the correct direction

Thanks

Pete
  0      
  0      
#1
Options
4 Reply
Re:R600VPN Config
2015-11-03 14:49:37 - last edited 2021-08-21 05:28:00
On site A, remote subnet should be 0.0.0.0/32, when the connection built up, route table in site B will looks like [dst:0.0.0.0 nexthop:site A]

I'm not sure will it work for you. I never tried, This is just what I thought about.
  0  
  0  
#2
Options
Re:R600VPN Config
2015-11-04 05:23:56 - last edited 2021-08-21 05:28:00
Thanks alphhha - I will test this evening and report back
  0  
  0  
#3
Options
Re:R600VPN Config
2015-11-04 13:02:18 - last edited 2021-08-21 05:28:00
alphhha - I get an error message when I try to add 0.0.0.0/32 in router 'A'.

Error code: 34011 Peer subnet is not correct.

I have attached an amended diagram. I can ping the 192.168.1.227, router A from 192.168.2.1, router B and the same in reverse. Router B can not ping the Internet router 192.168.1.1. I have a static route in the Internet router ponting 192.168.2.0/24 to 192.168.1.227/ Other devices on the 192.168.1.0/24 LAN can not ping 192.168.2.1, Any suggestions what I am missing

  0  
  0  
#4
Options
Re:R600VPN Config
2015-11-05 03:39:19 - last edited 2021-08-21 05:28:00
I have continued with my testing and have made progress, but I am not to the required configuration.

I have added a new graphic for further clarification



From PC A, I can ping PC B and PC B and ping PC A as well as the gateways. PC B can ping 192.168.1.1. I can ping the internet from PC A (8.8.8.8 - Google DNS). However, I can not ping the Internet from PC 'B'. I added a static route in router B 8.0.0.0/8 to 192.168.1.1 (Internet router) as well as router A address (192.168.1.227). neither of these worked.

Any thoughts? I would like to get working by next week, when I need to install the solution at its permanent location.
  0  
  0  
#5
Options