After setup admin page is not reachable anymore - no device is able to connect to Internet but OC200

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

After setup admin page is not reachable anymore - no device is able to connect to Internet but OC200

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
After setup admin page is not reachable anymore - no device is able to connect to Internet but OC200
After setup admin page is not reachable anymore - no device is able to connect to Internet but OC200
2024-09-19 20:04:30 - last edited 2024-09-21 14:16:55
Model: ER706W  
Hardware Version: V1
Firmware Version: 1.1.2 Build 20240726 Rel.77184(4555)

Strange issue ...

 

have resettled the router now several times - always ending at the same issue:

 

After the reset the setup wizard is working fine, router adminpage is accessible without issues. Standard config. But - as soon I connect the ISP modem (I see that the router get's the IP on the wan2 interface immediately) I can't access the admin page anymore. wLan is telling me "no internet connection"

 

Funny enough - as I also run a Omada controller (OC200) and this is the only device capable to access the internet - and is also reachable from external. At the OC200 Interface I see all devices - also the ER706W - but I'm also not able to adopt it ... 

 

There are NO vLan (except vlan1 by default) configured

There are no FW rules

 

The only thing I found was that if mesh is turned on it can cause issues - so mesh is disabled now - but no luck so far.

 

Any Idea what's going on here?

 

Regards

  0      
  0      
#1
Options
1 Accepted Solution
Re:After setup admin page is not reachable anymore - no device is able to connect to Internet but OC200-Solution
2024-09-21 14:16:44 - last edited 2024-09-21 14:16:55

found the issue ... in fact no DNS settings where set at the wan (normally I would guess these come automatically when ISP is connected to wan during the connectionwizard) and by default also my LAN DNS Entry were empty. No issue when no wan was connected but as soon it was availible the requests where sent to Nirvana ...

 

setting DNS manulally beforehand and also add DNS to teh LAN settingsd did the trick

Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:After setup admin page is not reachable anymore - no device is able to connect to Internet but OC200
2024-09-20 11:00:05

  @pur_berger 

 

it sounds like you get the same IP on the WAN as you do have on the LAN. try changing the LAN ip to e.g. 10.43.1.1/24 before connecting to the WAN

 

 

  0  
  0  
#2
Options
Re:After setup admin page is not reachable anymore - no device is able to connect to Internet but OC200
2024-09-21 08:01:01

  @pur_berger 

 

As above, or you have one or more devices with the same IP on the network which can cause all sorts of borkiness

Main: ER8411 x1, SG3428X x1, SG3452 x1, SG2428LP x1, SG3210 x1, SG2218P x1, SG2008P x1, ES205G x2, EAP650 x6 Remotes: ER605 v2 x3, SG2008P x2, EAP650 x2 VPN Server: ER7206 v2 Controller: OC300
  0  
  0  
#3
Options
Re:After setup admin page is not reachable anymore - no device is able to connect to Internet but OC200-Solution
2024-09-21 14:16:44 - last edited 2024-09-21 14:16:55

found the issue ... in fact no DNS settings where set at the wan (normally I would guess these come automatically when ISP is connected to wan during the connectionwizard) and by default also my LAN DNS Entry were empty. No issue when no wan was connected but as soon it was availible the requests where sent to Nirvana ...

 

setting DNS manulally beforehand and also add DNS to teh LAN settingsd did the trick

Recommended Solution
  0  
  0  
#4
Options