Business Community > Controllers > ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200
< Controllers

ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200

ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200

ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200
ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200
2024-05-24 00:24:47
Tags: #Adoption #Controller Installation #WAN
Model: OC200   ER605 (TL-R605)  
Hardware Version: V2
Firmware Version: 5.13.30.20

Hi,

 

Having some issues with getting internet (WAN) connection working when using the OC200 Omada Controller for an ER605v2, if I use the ER605 in standalone mode with the same settings set as what I do in the controller when the ER605 is adopted it failes to connect.

I have hard reset, power on, force etc. multiple times however I am just not able to resolve so hoping for some assistance.

 

Details are:

Router: ER605v2 Firmware Version 2.2.3 Build 20231201 Rel.32918

Controller: OC200 -  OC200 1.0, Controller Version 5.13.30.20, Firmware Version 1.29.4 Build 20240304 Rel.54362

 

The following shows the setup to the Omada Controller vs what was setup and working in the Router which connects with no issue at all in standalone.

 

 

  0      
 
  0      
 
#1
Options
5 Reply
Re:ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200
2024-05-24 09:05:33 - last edited 2024-05-24 09:06:26

Hi @mitchellfrankli 

Could you try to upgrade both the controller and ER605 V2 to the latest firmware and see whether it works?

Please download the latest firmware from our official websites below:

For ER605 V2, please upgrade to ER605(UN)_V2_2.2.4 Build 20240119.

For OC200 V1, please upgrade to OC200(UN)_V1_1.29.21 Build 20240401.


And here is the instruction to upgrade the controller. Please back up your file before upgrading. 

 

If rather, please also try to MAC clone one of your other device such as PC's MAC address and try again.

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200
2024-05-25 08:23:33

  Hi @Hank21,

 

Thanks heaps, I have updated both the Controller and Router to the latest as suggested however this unfortunately did not resolve. I reset the Router and re-provisioned from scratch and this unfortunately still did not resolve. I have checked the applciaiton results from the deployment and this also shows AOK so I am really lost as to why now it does not work.

Ta

Mitch

  0  
  0  
#3
Options
Re:ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200
2024-05-25 10:14:53

Have you tried power cycling your modem?

 

I had a similar issue where my internet connection would work when plugged into a Netgear router/AP combo unit, but when I plugged it into my ER8411 that was being managed by an OC300 it wouldn't show any activity. After completely wiping and rebuilding the router and controller several times, I tried cycling power to the modem, and that cleared it right up.

 

Different hardware, so it might not be it, but it might be worth a try if you haven't yet.

  0  
  0  
#4
Options
Re:ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200
2024-05-26 03:14:15

  @BHJohnson Thanks heaps, its not actually a bad idea since memory or other could be holding ontop something invalid however alas it did not resolve for me :(.

 

Spend a good 5 hours trying different ways to resolve but did not resolve so I will document them below (May give @Hank21 or   @BHJohnson another idea for me ;D)

 

1: Hard Reset (Front Reset pin) the Er605v2, created initial account, accessed oc200 controller, adopted and applied fresh config, confirmed no errors in deployment (application Beta) tab.

2: Force Re-Adopt to sync settings from oc200 Controller.

3: Hard Reset (Front Reset pin) the oc200, Force Re-Adopt of Er605v2.

3: Hard Reset (Front Reset pin) the Er605v2, oc200, initial setup in Er605v2 to get oc200 IP and applied fresh config for all.

4: Hard Reset (Front Reset pin) the Er605v2, oc200, initial setup in Er605v2 to get oc200 IP and applied fresh config for all.disconnected power for 5min and restart both Er605v2 & oc200

5: Hard Reset (Front Reset pin) the Er605v2, oc200, found oc200 ip without initial logon to Er605v2 and made fresh config , disconnected power for 5min and restart both Er605v2 & oc200

6: Hard Reset (Front Reset pin) the Er605v2, oc200 & SG2210MP (Jetsream Switch), initial setup in Er605v2 to get oc200 IP and applied fresh config for all.disconnected power for 5min and restart all three Er605v2, oc200 & SG2210MP

7: Hard Reset (Front Reset pin) the Er605v2, oc200 & SG2210MP (Jetsream Switch), found oc200 ip without initial logon to Er605v2 and made fresh config for all.disconnected power for 5min and restart all three Er605v2, oc200 & SG2210MP.

 

(Note: that all of the above have both been with using the default MAC address for the Er605 and MAC override to align with previous tp link vx220 modem.router

 

Current Item Models and Firmware:

ER605 v2.0: Firmware 2.2.4 Build 20240119 Rel.44368

OC200 1.0 :Controller Version 5.13.30.50, Firmware v1_1.29.21 Build 20240401

SG2210MP v4.20: Firmware  4.20.1 Build 20240115 Rel.72847

 

 

 

 

 

 

  0  
  0  
#5
Options
Re:ER605 Standalone Connects to Internet but fails when bening managed by Omada Controller OC200
2024-05-27 03:14:07

Hello @mitchellfrankli 

Thanks for your detail description. May I know who is your Internet service provider? And what is the model number of your modem? You can try to change the MTU to 1400 and see whether it works in controller mode.

 

Besides, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID TKID240548863, please check your email box and ensure the support email is well received. Thanks!

Once the issue is addressed or resolved, welcome to update this topic thread with your solution to help others who may encounter the same issue as you did.
 

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 456

Replies: 5

Tags

Adoption Controller Installation
WAN
Related Articles
Moving ER605 and EAP 245 to OC200 from software controler
193 0
OC200, after adopting ER605 the internet access stopped.
65 0
ER605 Standalone network segregation
485 0
adopting existing Omada gateway in new controller OC200
2325 0
ER605 Standalone is MAC filtering possible
4197 0
ER605 Standalone Configuration & Reported Nessus Vulnerability
1022 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.