This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.Problem with policy routing
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello everyone, I have a problem with my policy routing. I have 3 ISPs (WAN, WAN/LAN1, WAN/LAN2).
I created a VLAN (123), created a wireless network with this VLAN and routed it through WAN/LAN1.
At the moment, my WAN/LAN1 is offline, it should be, and I expect that there should be no Internet on my wireless network (VLAN123), because it is redirected through the WAN/LAN1 port, but the Internet works through WAN, or through WAN/LAN2, if WAN does not work.
Use the other WAN port, this checkbox is not selected.
The same problem with VLAN124 and the WAN/LAN2 port.
Load balancing has this setting
Hi @Hank21
today I did some more tests, and noticed that when WAN/LAN1 is offline, but has an IP address other than 0.0.0.0, then all the policy routing rules work as expected.
denis-odessit wrote
Hello everyone, I have a problem with my policy routing. I have 3 ISPs (WAN, WAN/LAN1, WAN/LAN2).
I created a VLAN (123), created a wireless network with this VLAN and routed it through WAN/LAN1.
At the moment, my WAN/LAN1 is offline, it should be, and I expect that there should be no Internet on my wireless network (VLAN123), because it is redirected through the WAN/LAN1 port, but the Internet works through WAN, or through WAN/LAN2, if WAN does not work.
Use the other WAN port, this checkbox is not selected.
The same problem with VLAN124 and the WAN/LAN2 port.
Load balancing has this setting
Have you also configured the Link Backup on Load Balancing? Try to disable the link backup and try again.
denis-odessit wrote
I just made the test with the configuration you provided and it works fine. That is, my VLAN 123 will lose Internet connection when the WAN/LAN1 offline, when the other VLAN is still having Internet connection via WAN and WAN/LAN2.
May I know the model and the firmware of your gateway? Please try to upgrade to the latest firmware and try again.
I have devices ER605 v2.0 (2.2.4 Build 20240119 Rel.44368), OC200 v2.0 (2.15.2 Build 20240410 Rel.31260) , TL-SG2428P v4.0 (4.0.8 Build 20240115 Rel.72847), 6xEAP225(EU) v4.0 (5.1.6 Build 20240313 Rel. 43415), 2xEAP245(EU) v4.0 (1.2.1 Build 20230824 Rel. 61490), EAP225-Outdoor(EU) v3.0 (5.1.6 Build 20240313 Rel. 43415), everything is updated to the latest versions
this is the complete routing policy table
@Hank21 ,
if WAN/LAN 1 is online everything works as expected, when I connect to the test wifi I get the address 192.168.101.11, if you do a trace route when wan/lan1 is offline, the traffic goes through WAN, I see the WAN gateway ip on the second hop, if WAN and WAN/LAN1 are not working (offline), on the second hop I see the WAN/LAN2 gateway ip, but if all 3 ISPs are online, on the second hop I see the WAN/LAN1 gateway ip as expected.
My WAN/LAN1 is a Starlink, and on shore it doesn't work, it only starts working a few miles from shore, and when I'm on shore the Starlink doesn't receive CGNAT, and the WAN/LAN1 gateway has ip 0.0.0.0, there may be a problem in this?
Hi @d0ugmac1,
I use Flat High Performance (maritime), when I'm in the port, I'm outside service address, and starlink gives me the address 192.168.100.100, and dishy has the address 192.168.100.1. I don't use a Starlink router at all
