inconsistency between documentation and ETH Port Settings.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

inconsistency between documentation and ETH Port Settings.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
inconsistency between documentation and ETH Port Settings.
inconsistency between documentation and ETH Port Settings.
2023-12-08 20:44:40 - last edited 2023-12-15 09:07:08
Model: EAP615-Wall  
Hardware Version: V1
Firmware Version:

When looking at the documentation 8https://static.tp-link.com/upload/image-line/EAP615_Wall_1.0_03_large_20210827080338k.jpg) is not matching the view when i look thru OC200 Device/EAP615/Config/Advance/ETH Port Settings

 

---

ETH Port Settings

ETH1 VLAN :
ETH2 VLAN :
ETH3 VLAN :
ETH3 PoE Out :
---
 
I would assume that ETH1 VLAN is really ETH0 (PoE IN), ETH2, is really 1 and ETH3 is really 2.
 
It would be helpful if ETH1 would be really as in the picture (with Additional test PoE IN)...
 
  0      
  0      
#1
Options
1 Accepted Solution
Re:inconsistency between documentation and ETH Port Settings.-Solution
2023-12-12 07:15:39 - last edited 2023-12-15 09:07:08

Hi @AntonV

 

Thanks for your valuable feedback! This has been forwarded to the developer team for attention and is planned to be optimized in the subsequent firmware iteration.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:inconsistency between documentation and ETH Port Settings.
2023-12-11 03:23:10

Hi @AntonV 

Thanks for posting in our business forum.

Here's the way to verify it.

EHT0 is the uplink, right? If you set up VLAN on the upstream switch/router, you don't bother to configure anything on this uplink port.

So, you configure ETH1 with another PVID X(except for 1), and you test it out on ETH1. Will you get the IP from the VLAN X?

This should verify what worries you and answer itself.

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Official and Beta firmware. NEW features! Subscribe for the latest update!Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting ★ ☚ ● Be kind and nice. ● Stay on the topic. ● Post details. ● Search first. ● Please don't take it for granted. ● No email confidentiality should be violated. ● S/N, MAC, and your true public IP should be mosaiced.
  0  
  0  
#2
Options
Re:inconsistency between documentation and ETH Port Settings.
2023-12-11 20:07:36

  @Clive_A Yes, I could actually figure out thru one youtube video (just to make sure that i am setting the right one). Point here is more that documentation/manuals/etc. need to be consistent thru GUI, pdfs, pictures.

thank you.

Clive_A wrote

Hi @AntonV 

Thanks for posting in our business forum.

Here's the way to verify it.

EHT0 is the uplink, right? If you set up VLAN on the upstream switch/router, you don't bother to configure anything on this uplink port.

So, you configure ETH1 with another PVID X(except for 1), and you test it out on ETH1. Will you get the IP from the VLAN X?

This should verify what worries you and answer itself.

 

  0  
  0  
#3
Options
Re:inconsistency between documentation and ETH Port Settings.-Solution
2023-12-12 07:15:39 - last edited 2023-12-15 09:07:08

Hi @AntonV

 

Thanks for your valuable feedback! This has been forwarded to the developer team for attention and is planned to be optimized in the subsequent firmware iteration.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#4
Options