Beta Software ER707-M2 V1_1.1.1 Build 20230927 Beta Firmware for Omada Controller v5.12 (Released on Sep 27, 2023)
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
This Article Applies to
ER707-M2 V1 / V1.6_1.1.1_Build 20230927 (Beta)
- Fully adapted to Omada SDN Controller 5.12.
Release Notes
New Feature/Enhancement
1. Add ACL support for IPv6 data.
2. Add support for IPv6 RA (Router Advertisement) configuration for LAN.
3. Add support for configuring multiple IP addresses on the WAN port.
4. Add support for monitoring session limits in controller mode.
5. Add support for configuring the MSS (Maximum Segment Size) of WAN port.
6. Add support for Gateway Tools in Controller mode.
- Ping.
- Traceroute.
- Terminal.
7. Add support for the ability to download device info of Gateway in Controller mode.
8. Add support for Location Group in Gateway ACL.
9. Add support for allow list of MAC filtering in Controller mode.
10. Add support for tagging same VLAN ID on different WAN port.
11. Increased security of communication between Gateway and Controller.
12. Add support for DNS cache, which can improve domain name resolution speed by handling recent address resolutions locally before sending request to Internet .
13. Add support for DH 14 and DH 15 for PFS.
14. Add support for 0.0.0.0/0 IP range of local network when using IPsec IKEv2 for Client-to Site VPN.
15. Add support for DDNS custom intervals (1~60 minutes).
16. Add support for link-local addresses of IPv6 DNS on the LAN side.
17. Log Enhancements.
- Show the source IP address of TCP no-Flag /ping of death attacks.
- Show the log of link backup switching.
- Show the log of DDNS update.
- Logs can be saved when the device is down. You need to short press the reset button within 5s, and after releasing the reset button, the sys light will be on for 3 seconds to indicate that the downtime log is saved successfully.
18. Add support for Intrusion Detection/Prevention
19. Add support for Deep Packet Inspection in Standalone mode.
20. Add support for enable/disable Flow Control in Controller mode.
21. Add support to modify the rate and duplex of the Ethernet port in Controller mode.
Bug Fixed
1. Fix the bug that ICMP type 13 packets cannot be intercepted
2. Fix the bug that VPN Client cannot access the other side through IPsec when the device act as a PPTP/L2TP/OpenVPN Server and also establishes IPsec VPN with other devices.
3. Fix the bug that VPN client cannot proxy Internet access when VPN IP Pool and LAN IP are in the same network segment.
4. Fix the bug of CPU abnormality caused by enabling more VLAN Interface.
5. Fix the bug of high latency in ISP Load in Controller mode.
6. Fix the bug of frequent reconnection with Omada Controller.
7. Fix the bug that the VLAN configuration of IPTV is affected by the VLAN configuration of WAN port in Controller mode.
8. Fix the bug that the device does not support proxy internet access as Wireguard VPN client.
9. Fix the bug that Port Forwarding does not take effect under multiple WAN ports.
10. Fix the bug that the port status display is abnormal in Controller mode.
11. Fix bugs related to OpenVPN:
- OpenVPN clients cannot proxy Internet access through the device.
- OpenVPN IP pool cannot be configured.
- When the device is used as an OpenVPN Server and the option is Split mode, OpenVPN clients cannot access the Internet normally.
- Remote IP error displayed in the OpenVPN Tunnel interface when the device connects successfully as an OpenVPN Client.
- When the device acts as an OpenVPN Client, OpenVPN fails to start when there are unsupported fields in the OVPN file.
12. Fix the bug that cloud access could not connect successfully when PPPoE dialup was performed on the WAN port.
13. Fix the bug that after the device connects to the Server as a WireGuard VPN Client, the peer cannot access the device via WireGuard Interface IP.
14. Fix a bug that prevented successful login when an underscore was used for the login password
Firmware Download
Before the Upgrade
(1) Please be sure you have read the Beta Test Agreement before upgrading the Beta firmware!
(2) You may follow the following guide to upgrade your Omada devices. How to Upgrade/Downgrade Omada Gateways
Firmware Download Link
ER707-M2 V1_1.1.1_Build 20230927 (Beta)
Notes:
(1) The above firmware is applied to ER707-M2 V1 and V1.60.
(2) Your device’s configuration won’t be lost after upgrading.
(3) The new features added in the above firmware require to upgrade of the Omada SDN Controller 5.12, which has been released for early access here.
Additional Information
All feedback is welcome, including letting us know about successful device upgrades.
If somehow you encounter an issue during or after the ER707-M2 Router upgrade, it's suggested to contact us with the following info:
- Omada Controller version
- Device Firmware version with Build number (previous and current)
If your ER707-M2 router gets bricked during the firmware upgrade, you may follow the guide below to recover the firmware.
How to use the Emergency Mode to recover the firmware for Omada Gateways
Update Log
Nov. 20th, 2023:
Update the format and incorrect description in the release note.
Sep 27th, 2023:
Post the ER707-M2 V1 / V1.6_1.1.1_Build 20230927 (Beta) firmware for early access.
Recommended Threads
Get the Latest Firmware Releases for Omada Routers Here - Subscribe for Updates
Get the Latest Omada SDN Controller Releases Here - Subscribe for Updates
Experience the Latest Omada EAP Firmware - Trial Available Here, Subscribe for Updates!
Current Available Solutions to Omada Router Related Issues [Actively Updated, Post for Subscription]
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi @drbanan
Thanks for posting in our business forum.
drbanan wrote
@Clive_A ISP is 2/1 on #1, on #2 i had either my pc, ubuntu server (both have 2.5gbe cards) or TL-SX3008F with sfp+ 10gbe.
Problem:
#1 ISP, #2 my pc - 2gbit down, 300mbit up#1 ISP, #3 my pc - 1/1gbit
#2 my pc #3 ubuntu server - 1gbit down, 300mbit up on my pc
Yes, i tried multiple cables
I have TL-SX3008F switch - i am able to saturate about 4/10gbit on windows machine from server on this switch.
Controller is up to date - Software Omada (hosted on windows)
WAN config - pppoe, nothing fancy put in, but if there is any special option please ask i will provide. I just tried Flow Control (anyway, what is this? can't find info) and it didn't help.
Tried all available FW versions - even beta one 1.1.1 - not helping.
Got kinda offtop, but same metric question - should 2.5gbe work on 10gb sfp+ transceiver via TL-SX3008F? Even if i am able to run it on router+pc, that i will be able to route it further to switch like this: 2.5gbe(ER707-M2)<->10gbe sfp+(TL-SX3008F) using TL-SM5310-T on switch sfp+ side
Do you mean the #2 port always get limited to 1Gb-down 300Mbps-up? Confirm this to make sure I understand you right.
PPPoE. Huh. I need to ask the dev team about this.
- Copy Link
- Report Inappropriate Content
Hi @drbanan
Thank you so much for taking the time to post the issue on TP-Link community!
To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID is TKID231229870, please check your email box and ensure the support email is well received. Thanks!
Once the issue is addressed or resolved, welcome to update this topic thread with your solution to help others who may encounter the same issue as you did.
Many thanks for your great cooperation and patience!
- Copy Link
- Report Inappropriate Content
@Clive_A If i could sum it up - #2 2.5gbe port using 2.5gbe connection on both ends always ends up with only 300mbit upload. When i force switch this port (#2 2.5gbe) to 1 gbe it gets full 1gbit up. Download on this port seems fine all the time. (saturates 2gbit ISP when it is on 2.5gbe mode, and saturates 1gbit when port is in 1gbit mode)
- Copy Link
- Report Inappropriate Content
Hi @drbanan
drbanan wrote
@Clive_A If i could sum it up - #2 2.5gbe port using 2.5gbe connection on both ends always ends up with only 300mbit upload. When i force switch this port (#2 2.5gbe) to 1 gbe it gets full 1gbit up. Download on this port seems fine all the time. (saturates 2gbit ISP when it is on 2.5gbe mode, and saturates 1gbit when port is in 1gbit mode)
I have created a case for you and I've sent an email privately to your registered email address. If you don't reply, I will mark the case as closed.
I have asked what information I need in the email. Please respond to my email.
In addition, can you wire your PC to the modem and test it? Paste the result here or in the email response.
- Copy Link
- Report Inappropriate Content
@Clive_A I think i provided all necessary information - 1gbit port works like a charm - i can saturate 1/1gbit on it, but when i connect to 2.5gbit port i can saturate it to 2.5gbit download and 300mbit upload, and it doesn't matter if it's speedtest via my ISP or LAN transfer, always up is limited.
I have 10gbit switch and when i transfer data between devices using it i can saturate 10/10gbit using SMB or iperf3. Devices work perfectly. It's ALL about port #2 on ER707-M2 that is broken.
When i first tested config was default, didn't change dime on it on switching side (fresh install), and it doesn't matter if it is standalone version, or omada controlled - always same problem, only ~300-350mbit upload on port #2. Also changing every possible option on config didn't change anything, always same result.
Now this port is connected to 10gbe SFP+ <-> 2.5gbe #2 on ER707-M2, but i also connected DIRECTLY to it (2.5gbe my pc <-> 2.5gbe ER707-M2) from my motherboard that has 2.5gbe and i have SAME speed - 300-350mbit up. When i change port #2 to 1gbit only, it works as intended (1/1gbit), but it's not using it's full potential of 2.5/2.5gb
The software is broken, there is no single option i have something wrong on my side - checked all possible options. I have even 2 mobos with 2.5gbe, one is on ubuntu server - same speed.
Replying to mail in a short
- Copy Link
- Report Inappropriate Content
@Clive_A After many further tests and going without full usual network config, just my pc + server + router i figured out where exactly problem is.
If i set ANY of the ER707-M2 2.5GbE ports to 2.5G, than UPLOAD on these ports gets lowered
Setup:
ISP 2.5GbE <-> ER7070-M2 port #1 2.5GbE
My PC 2.5GbE <-> ER707-M2 port #2 2.5GbE
When port #1 and #2 are changed to 1GbE i can saturate 1/1gbit on ISP. Changing ANY of these ports to 2.5GbE lowers this exact port UPLOAD speed.
Tests via iperf3 on outside server (it is on 10gbit, i can saturate my whole net on secondary router):
port #1 1GbE and port #2 to 2.5GbE then -> my pc gets 1gbit download ~400-500mbit upload
port #1 2.5GbE and port #2 to 1GbE then -> my pc gets ~400-500mbit download 1gbit upload
port #1 2.5GbE and port #2 to 2.5GbE then -> my pc gets 600-1600mbit download 150mbit upload (higher download due to ISP providing 2050mbit download)
Looks like UP on any of these ports gets around halved whenever switching it to 2.5GbE.
But most interesting part is - if i switch port #2 to 2.5GbE and connect secondary PC on port #3 then i have 1/1gbit between these PCs
Something is here totally fcked up on 2.5GbE switching side
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 7818
Replies: 26
Voters 0
No one has voted for it yet.