Business Community > WiFi > Business (or Industrial Version) of Deco Mesh System
< WiFi

Business (or Industrial Version) of Deco Mesh System

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Business (or Industrial Version) of Deco Mesh System

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Business (or Industrial Version) of Deco Mesh System
Business (or Industrial Version) of Deco Mesh System
2023-09-10 23:05:55 - last edited 2023-09-12 01:55:49

Hi There

 

TP-Link site/marketing isn't that easy to follow...  

 

I'm looking for a Business or Industrial AP that implements a mesh network as per Deco systems, and at the value end of that market. Has TP-Link produced such a product thus far?

 

The Deco systems work fine for how we use them with robotics in our own industrial manufacturing site; what I'm trying to find is the same capability but packaged in professional-looking housing.

 

All the business AP I've found seem to be only wired backbone connection? 

 

 

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Business (or Industrial Version) of Deco Mesh System-Solution
2023-09-11 09:51:33 - last edited 2023-09-12 01:55:49

Hello @MHMMike,

 

You may refer to this article to learn more details of the difference between the Omada Mesh and Deco Mesh.

 

To establish the Omada mesh network, you will need to connect one EAP to the router/switch via Ethernet cable, and the other EAPs will be able to wirelessly connect to each other. With the mesh network, you just need to power on the other EAPs, and they will not need to connect to the router/switch via Ethernet cable.

Please note that:
1) You will need to configure the Mesh network on the controller. So please download a software controller or purchase a hardware controller like OC200.

2) Normally, it is suggested for you to run the controller all the time. You can check more detailed information about mesh network here.
3) Here is a guide to set up mesh network.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options
2 Reply
Re:Business (or Industrial Version) of Deco Mesh System-Solution
2023-09-11 09:51:33 - last edited 2023-09-12 01:55:49

Hello @MHMMike,

 

You may refer to this article to learn more details of the difference between the Omada Mesh and Deco Mesh.

 

To establish the Omada mesh network, you will need to connect one EAP to the router/switch via Ethernet cable, and the other EAPs will be able to wirelessly connect to each other. With the mesh network, you just need to power on the other EAPs, and they will not need to connect to the router/switch via Ethernet cable.

Please note that:
1) You will need to configure the Mesh network on the controller. So please download a software controller or purchase a hardware controller like OC200.

2) Normally, it is suggested for you to run the controller all the time. You can check more detailed information about mesh network here.
3) Here is a guide to set up mesh network.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options
Re:Business (or Industrial Version) of Deco Mesh System
2023-09-11 20:13:53

  @Hank21 

 

Thank you very much.  I would never have figured that out unless stumbled across those pages.

  1  
  1  
#3
Options

Information

Helpful: 0

Views: 791

Replies: 2

Related Articles
 WiFi Mesh for Business
267 0
 SYS not blinking
1298 0
 EAP 225 into an industrial shed
249 0
Business equipment support
304 0
Network Design for Small Business
869 0
Version differences between versions
403 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.