Business Community > Routers > ER605 - question about CLI security
< Routers

ER605 - question about CLI security

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER605 - question about CLI security

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER605 - question about CLI security
ER605 - question about CLI security
2023-08-22 23:29:30 - last edited 2023-09-11 02:28:28
Model: ER605 (TL-R605)  
Hardware Version: V2
Firmware Version: 2.1.2 Build 20230210 Rel.62992

Quick check: if I enable CLI mode on the router (Remote Assistant feature), is the SSH login available on the WAN as well, or only LAN ports? I'd like to be able to configure the router from the LAN excluding any potential attacks to the router from the outside.

 

Reason: sometimes I need to reconfigure the network remotely, but I have nothing else than elinks/lynx text web-browsers which are not handled by the WWW interface of the router.

  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:ER605 - question about CLI security-Solution
2023-08-23 03:05:13 - last edited 2023-09-11 02:28:30

  @consmast

if remote access management is enabled, your device is available via WWW and SSH.

 

 

ScReW yOu gUyS. I aM GOinG hoMe. —————————————————————— For heaven's sake, can you write and describe your issue based on plain fact, common logic and a methodologic approach? Appreciate it.
Recommended Solution
  0  
  0  
#2
Options
Re:ER605 - question about CLI security-Solution
2023-08-23 08:37:45 - last edited 2023-09-11 02:28:28

  Ive just tested on my ER605 and enabling Remote Assistance in the Diagnostics menu ONLY allows SSH access from the local LAN.

It will ONLY be accessible remotely ( via SSH and HTTP/S ) if you enable Remote Management in the Admin Setup menu and then only from any IP subnets you define as allowed access

Recommended Solution
  1  
  1  
#3
Options
3 Reply
Re:ER605 - question about CLI security-Solution
2023-08-23 03:05:13 - last edited 2023-09-11 02:28:30

  @consmast

if remote access management is enabled, your device is available via WWW and SSH.

 

 

ScReW yOu gUyS. I aM GOinG hoMe. —————————————————————— For heaven's sake, can you write and describe your issue based on plain fact, common logic and a methodologic approach? Appreciate it.
Recommended Solution
  0  
  0  
#2
Options
Re:ER605 - question about CLI security-Solution
2023-08-23 08:37:45 - last edited 2023-09-11 02:28:28

  Ive just tested on my ER605 and enabling Remote Assistance in the Diagnostics menu ONLY allows SSH access from the local LAN.

It will ONLY be accessible remotely ( via SSH and HTTP/S ) if you enable Remote Management in the Admin Setup menu and then only from any IP subnets you define as allowed access

Recommended Solution
  1  
  1  
#3
Options
Re:ER605 - question about CLI security
2023-09-10 17:19:57

Thank you Guys!

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1198

Replies: 3

Related Articles
Question before purchase ER605
728 0
 CLI console for ER605
857 10
 WARNING: ER605 Security Vulnerability..!
4269 1
DHCP server set ip range over CLI
236 1
 ER605/Best Firewall Security settings
2848 0
ER605 Access Control Question (Block WAN to specific VLAN but allow other LAN)
559 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.