CPE510 always have unsaved changed after boot

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

CPE510 always have unsaved changed after boot

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
CPE510 always have unsaved changed after boot
CPE510 always have unsaved changed after boot
2023-07-09 07:43:22 - last edited 2023-07-09 07:44:25
Tags: #Firmware
Model: CPE510  
Hardware Version: V3
Firmware Version: 2.2.3 Build 20230222 Rel. 37905

Save changes in the web-interface, reboot and log back in and there are unsaved changes again. This happens with all the firmware-releases I have tried, and is the same on all my CPE's. It seems that something in boot-process trips the config-change detection. The CPE works, but such a bug makes me question the reliability of the device. The bug has existed for at least 3 years as I have tested firmware released from 2020 through 2023. The problem has been reported, but support has not acknowledged it as a bug.

 

The inability to keep track of config-changed combined with the CPE's inability to log anything useful locally, to syslog server or via SNMP traps makes it near impossible to solve issues with the device. 

  0      
  0      
#1
Options
5 Reply
Re:CPE510 always have unsaved changed after boot
2023-07-10 07:51:05

  @PerHe 

 

What specific settings are you referring to? Is it Tools settings can not be saved?

I'm experiencing the same issue, and it appears to be a normal behavior based on the design.

Just striving to develop myself while helping others.
  0  
  0  
#2
Options
Re:CPE510 always have unsaved changed after boot
2023-07-10 21:08:28 - last edited 2023-07-10 21:09:25

  @Virgo The point is that the firmware indicate that the configuration has changed even is nobody has touched anything. The firmware indicate that something has has been changed, but no details.

  1  
  1  
#3
Options
Re:CPE510 always have unsaved changed after boot
2023-07-15 12:08:33 - last edited 2023-07-15 12:09:28

  @PerHe I have come to just accept this as normal. On all of my CPE710 units, I hit apply, it reloads the page, and then prompts me to save changes. I hit save and move on.

 

Is yours always showing save or can you click save and it stops until you make another change and apply?

  0  
  0  
#4
Options
Re:CPE510 always have unsaved changed after boot
2023-07-22 07:21:57

  @RickJamesBish I wouldn't complain about change-notification if I make changes. That is how things are supposed to work. The problem is that the device indicate that changes have been made although I'm certain nothing has changed. If the device can't keep track of changes how can I then trust it to keep doing what I have configured it to? There is also the issue of the CPE's requiring reboot every now and then which adds suspicion wrt the integrity of either the firmware or RAM ... or both. I doubt it is hardware as the problem applies to all CPE's. Probably a software issue. Could for example be corrupted pointers messing up the running config. That could trip change-detection and cause a failure that require reboot. That is impossible to truoubleshoot when there is no event-logging implemented (except from logging boot-time and IP-address set during boot). I need devices that I can trust so I'm looking for a more reliable alternative. 

  0  
  0  
#5
Options
Re:CPE510 always have unsaved changed after boot
2023-07-22 18:41:39

  @PerHe its a long shot but check your time settings under system tab. Make sure timezone is correct and sync with PC clock.

  0  
  0  
#6
Options