Business Community > WiFi > EAP 225 ceiling mount wont proved greater than~90Mbps
< WiFi

EAP 225 ceiling mount wont proved greater than~90Mbps

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP 225 ceiling mount wont proved greater than~90Mbps

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP 225 ceiling mount wont proved greater than~90Mbps
EAP 225 ceiling mount wont proved greater than~90Mbps
2023-07-07 23:10:16
Model: EAP225  
Hardware Version: V3
Firmware Version:

Hello everyone

 

We recently had a huge outage with our neighborhood fiber, and since then my EAP225s do not exceed 90Mbps down or up.

 

I have had my ONT switched out, and all lines out of the router and switches exceed, on average 700Mbps up and down. The CAT cables feeding the POE injectors measure the same speeds. 

 

Setup the EAPs per TP link recommendations at both the 2.4 and 5Ghz radios.

 

 

Does anyone else know what else may be causing this limitation to the wifi signal?

 

  0      
 
  0      
 
#1
Options
5 Reply
Re:EAP 225 ceiling mount wont proved greater than~90Mbps
2023-07-08 07:43:50

  @MauroCampos  90Mbs is suspiciously close to 100Mb/s : is the Ethernet cable connecting at 1Gbs ok?

 

MauroCampos wrote

Hello everyone

 

We recently had a huge outage with our neighborhood fiber, and since then my EAP225s do not exceed 90Mbps down or up.

 

I have had my ONT switched out, and all lines out of the router and switches exceed, on average 700Mbps up and down. The CAT cables feeding the POE injectors measure the same speeds. 

 

Setup the EAPs per TP link recommendations at both the 2.4 and 5Ghz radios.

 

 

Does anyone else know what else may be causing this limitation to the wifi signal?

 

Could be a cable fault,or a speed negotiation issue.

 

Just a thought.

  0  
  0  
#2
Options
Re:EAP 225 ceiling mount wont proved greater than~90Mbps
2023-07-08 11:09:39
The ethernet cable entering each of the POE injectors is reading 1G when i connect my laptop. My understanding is I cannot connect my laptop to the POE cable if powered.
  0  
  0  
#3
Options
Re:EAP 225 ceiling mount wont proved greater than~90Mbps
2023-07-09 02:32:17

  @MauroCampos You can connect your laptop to a 802.3af/at poe powered cable...besides the pins are dc isolated anyways.

 

Make sure you do your testing with the 5.8G radios, it is entirely possible that you cannot get more than 90M in your local 2.4G environment.

<< Boycotting this site and these products until CANADIAN firmwares get some love >>
  0  
  0  
#4
Options
Re:EAP 225 ceiling mount wont proved greater than~90Mbps
2023-07-10 12:18:29

  @d0ugmac1 

 

I am measuring the same speeds at the switch and on the line side of the POE injectors. So 500Mbps or greater. It appears the slowdown is now at the WAP

  0  
  0  
#5
Options
Re:EAP 225 ceiling mount wont proved greater than~90Mbps
2023-07-10 12:38:24
Did you temporarily disable the 2.4G radio for your test? 90Mbps is exactly what I get on a 225 outdour on 2.4G...if I force it to 5.8G, then I get close to line rate of my ISP.
<< Boycotting this site and these products until CANADIAN firmwares get some love >>
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 741

Replies: 5

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.