ER7206 1.3.0 ACL completely broken

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER7206 1.3.0 ACL completely broken

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER7206 1.3.0 ACL completely broken
ER7206 1.3.0 ACL completely broken
2023-05-06 14:28:59
Model: ER7206 (TL-ER7206)  
Hardware Version: V1
Firmware Version: 1.3.0 official

Trying to set up some ACLs in firmware 1.3.0 is completely broken

 

I have some IP groups set up, and the exact same ACL settings i am trying to apply on my ER605v2 (latest beta) works without issue..

 

Problem - on entering all of the required info on the ACL screen, clicking "add" results in a red border and "Failed" message.  Clicking to another section on the GUI and going back does show the ACL in the list, but it is non functional.  Trying to delete the ACL results in same red border and "Failed" message.  Again, going somewhere else and then back in the GUI shows the ACL is indeed deleted

 

I need to set these ACLs up to harden the network, please fix

  0      
  0      
#1
Options
4 Reply
Re:ER7206 1.3.0 ACL completely broken
2023-05-07 08:30:17

  @GRL 

 

wild guest ,=>

 

didn't the last beta's 605 FW's support already Statefull ACL  (I know the V1 has it , don't know about 605 V2 ) 

And the official 1.3.0 doesn't state that it supports Statefull ACL.     Maybe how ACL are are configured change between the versions 

 

so you might be trying to do stuff the FW doesn't support yet ?

 

 

  0  
  0  
#2
Options
Re:ER7206 1.3.0 ACL completely broken
2023-05-07 14:47:05

  @mehmeh 

 

nope, ACLs have been present since the first ever firmware.  Im not doing anything that hasnt worked in any previous releases.

  0  
  0  
#3
Options
Re:ER7206 1.3.0 ACL completely broken
2023-05-08 06:54:19

Hello @GRL,

 

Could you provide a screenshot of the ACL-related settings? Which kind of ACL you are setting?

 

GRL wrote

Problem - on entering all of the required info on the ACL screen, clicking "add" results in a red border and "Failed" message.  Clicking to another section on the GUI and going back does show the ACL in the list, but it is non functional.  Trying to delete the ACL results in same red border and "Failed" message.  Again, going somewhere else and then back in the GUI shows the ACL is indeed deleted

 

Please share a screenshot of the red border and the error message.

Have you tried rebooting the gateway or the controller for testing?

 

Do you mean this issue only happens on firmware version 1.3.0?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options
Re:ER7206 1.3.0 ACL completely broken
2023-05-26 06:33:13

Hello @GRL,

 

Hope you are doing well. I’m wondering whether your concern was resolved finally?

If your concern was resolved, welcome to update this topic thread and share your solution so that others may benefit from it.

If not, you may tell us more details about your issue, the questions in my last reply are just for your reference.

 

We are looking forward to hearing from you again.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options