Business Community > Controllers > IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
< Controllers

IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-08 08:57:17 - last edited 2023-04-19 05:51:06
Tags: #Firmware Update
Model: OC200   ER605 (TL-R605)   SG2210P  
Hardware Version: V1
Firmware Version: 1.24.0 Build 20230328 Rel.52384 (Beta)

Controller

  • Model: OC200 v1.0
  • Controller Version: 5.9.32
  • Firmware Version 1.24.0 Build 20230328 Rel.52384 (Beta) [2023-04-07]

 

Router

  • Model: ER605 v1.0
  • Firmware Version: 1.2.2 Build 20230328 Rel.58400 (Beta) [2023-03-30]

 

Switch(es)

  • Model: TL-SG2210P v5.0
  • Firmware Version: 5.0.5 Build 20221130 Rel.42340

 

Before updating my OC200 v1.0 controller to Omada Hardware Controller V5.9.32 Beta, I was able to use IP-MAC Binding on my ER605 v1.0 router.

Now this option is not available anymore under 'Network Security'. When adding #ipMacBinding to the URL, the following message appears: Your current gateway does not support this feature, and the configuration page will be hidden:

 

  1      
 
  1      
 
#1
Options
1 Accepted Solution
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta-Solution
2023-04-15 16:20:11 - last edited 2023-04-17 01:54:41

Hi @Hank21, I just installed ER605 V1_1.2.3_Build 20230413 Beta and guess what? IP-Mac Binding is available again under 'Network Security'. Even including all settings I set before. So, the proof is there wink.

 

The only thing was that a new option 'Permit the packets matching the IP-MAC Binding entries only' is implemented (unlike in the previous beta) and checked, as a result of which the connection between the WAN-port of my ER605 router and my internet modem was completely blocked, because the IP address of my internet modem is not bound. So, however 'Permit the packets matching the IP-MAC Binding entries only' works, it would have been nice if this was mentioned in the release notes.

Recommended Solution
  1  
  1  
#11
Options
10 Reply
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-10 10:11:19

Hello @WM1，

 

WM1 wrote

Before updating my OC200 v1.0 controller to Omada Hardware Controller V5.9.32 Beta, I was able to use IP-MAC Binding on my ER605 v1.0 router.

 

May I know the firmware version of OC200 and the ER605 v1 as you said above?

 

I'm afraid that ER605 V1 doesn't support IP-MAC binding in controller mode at present.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-10 20:57:14 - last edited 2023-04-10 21:00:25

  @Hank21 

 

ER605: ER605v1_un_1.2.2_20230328(Beta)

OC200: OC200(UN)_V1_1.20.1 Build 20220921

 

I definitely used to be able to set IP-MAC Binding on the two sites I have. After upgrading the ER605 to the latest beta it was still avalable. After updating the OC200, the option was gone.

  0  
  0  
#3
Options
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-11 09:57:02

 Hi @WM1,

 

WM1 wrote

I definitely used to be able to set IP-MAC Binding on the two sites I have. After upgrading the ER605 to the latest beta it was still avalable. After updating the OC200, the option was gone.

 

I'm a little bit confused, as far as I'm concerned, ER605 V1 doesn't support IP-MAC binding.

Could you downgrade the firmware version of OC200 back to the original one and share a screenshot to show that?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-11 19:00:36

Hi  @Hank21, hopefully I have the time to downgrade and share a screenshot upcoming weekend. Meanwhile, you will have to trust me that this is/was possible laugh.

  0  
  0  
#5
Options
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-11 21:32:24

 Hello together.

 

I have a ER605 V2 but in December 2022 I take it out from my network because it has to many trouble with disconnects.

A key feature for my config is the IP-MAB binding.

Do any body know if the ER605 V2 has the same troubles with config?

 

Greetings Thorsten.

  0  
  0  
#6
Options
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-12 00:49:02

Hi @WM1,

 

It's OK, take your time.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#7
Options
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-12 00:56:38

Hello @Totti_14 ,

 

Please tell me the firmware version of your ER605 and the controller.

 

Totti_14 wrote

A key feature for my config is the IP-MAB binding.

Do any body know if the ER605 V2 has the same troubles with config?

 

As for the disconnect issue, there is a solution post you may refer to.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#8
Options
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-12 09:50:32

Hello  @Hank21 

 

My controller has actually the Firmware 5.7.6 but if I have time I like to try the new V5.9.32 Beta.

 

My ER605 V2 hast the Beta from December and I has a lot oft trouble with my family about the unstable WAN connection.

So I change back to my Friitz!BOX Router an I use the TP Link Controler OC200 / 4 Switches / and 4 EAP's without Routing (Gateway) Function.

 

If the IP-MAC Binding and the WAN connection will be stable I like to try to use the ER605 V2.

That's a lot of configuration work and the my Cable Fritz!Box 6591 is then only for Telephone and Modem. 

 

Greetings, Thorsten.

  0  
  0  
#9
Options
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta
2023-04-14 19:41:06

Hi @Hank21, I wanted to downgrade but that will mean that I will loose all my precious settings. It will take me too much time to revert to the previous version.

 


Can I ask you to reproduce yourself?

 

As mentioned I'm absolutely sure that IP_MAC Binding was available under 'Network Security' when my OC200 controller was at OC200(UN)_V1_1.20.1 Build 20220921. I also used IP-MAC Binding on my previous TL-R600VPN in stand alone mode. I set the ER605 in controller mode up in the same way.

  0  
  0  
#10
Options
Re:IP-MAC Binding unavailable after update to Omada Hardware Controller V5.9.32 Beta-Solution
2023-04-15 16:20:11 - last edited 2023-04-17 01:54:41

Hi @Hank21, I just installed ER605 V1_1.2.3_Build 20230413 Beta and guess what? IP-Mac Binding is available again under 'Network Security'. Even including all settings I set before. So, the proof is there wink.

 

The only thing was that a new option 'Permit the packets matching the IP-MAC Binding entries only' is implemented (unlike in the previous beta) and checked, as a result of which the connection between the WAN-port of my ER605 router and my internet modem was completely blocked, because the IP address of my internet modem is not bound. So, however 'Permit the packets matching the IP-MAC Binding entries only' works, it would have been nice if this was mentioned in the release notes.

Recommended Solution
  1  
  1  
#11
Options

Information

Helpful: 1

Views: 1635

Replies: 10

Tags

Firmware Update
Related Articles
How to binding MAC - IP on omada cloud
100 0
 ER605 IP-Mac Binding
1130 0
IP-MAC Binding don't exist in router ER8411
750 1
 OC300 ER8411 IP Mac Binding
557 0
 IP-Mac-Binding feature broken
737 0
 ER605 Mac Filter IP Binding
1740 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.