Business Community > Switches > PoE for the entire switch keeps failing
< Switches

PoE for the entire switch keeps failing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

PoE for the entire switch keeps failing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
PoE for the entire switch keeps failing
PoE for the entire switch keeps failing
2023-03-05 17:15:09
Tags: #PoE
Model: TL-SG2428P  
Hardware Version:
Firmware Version:

My switch keeps entering a state where it will no longer provide any PoE output, while the fans are also in a permanently elevated speed. It still provides data, but no power. This persists until I reset the switch (forcing me to readopt). It happened once a couple months ago, but now it happens every day. There's nothing in the controller logs indicating a problem.
 

The switch is plugged into a CyberPower CP1500PFCRM2U UPS. Is that possibly the culprit, or do I need to RMA the switch?

  0      
 
  0      
 
#1
Options
6 Reply
Re:PoE for the entire switch keeps failing
2023-03-06 07:20:26

Hi @curl2bash 

 

Have you tried to reset this switch and upgrade the firmware of it?

 

It looks like a hardware issue, and yes you can contact local support team and request warranty service.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:PoE for the entire switch keeps failing
2023-03-06 14:56:46

  @Hank21 I've reset it a few times (it's the only way to get PoE online again), and it just eventually fails again. There's also no pending updates for it, it's running 1.1.7.

  0  
  0  
#3
Options
Re:PoE for the entire switch keeps failing
2023-03-07 15:37:49

  @curl2bash That is very similar to the issue I had on a SG2428MP. Support wanted the log files from the switch, After that it had to go back, RMA. Mine started off doing once every few weeks, then progressed to just a few minuted between hang up. It, like yours dropped everything POE. There was also one wired wired client that it would drop. Probably you should just contact support.

 

 

  1  
  1  
#4
Options
Re:PoE for the entire switch keeps failing
2023-03-09 15:29:56

  @curl2bash 

 

Definitely sounds like a hardware fault.  If you have a voltmeter you could check the output of the switch's PSU and validate it against the rating...ie 53.5V or whatever, but it sounds much more like internal modules are faulty and that's RMA time.

<< Paying it forward, one juicy problem at a time... >>
  0  
  0  
#5
Options
Re:PoE for the entire switch keeps failing
2023-04-01 06:50:00

  @curl2bash 

It is possible that the CyberPower CP1500PFCRM2U UPS is the culprit. It could be drawing too much power when connected to the switch, causing the PoE to fail. You may want to try disconnecting the UPS and see if that resolves the issue. If not, then you may need to RMA the switch. Make sure to contact the manufacturer's support team for additional assistance.

  0  
  0  
#6
Options
Re:PoE for the entire switch keeps failing
2023-04-01 14:41:03
Pretty sure a few hundred watts of POE switch isn't going to overload a 1500VA (~1.5kW) UPS. That said, it's a good idea to take it out of the loop and test just to eliminate it as a potential issue.
<< Paying it forward, one juicy problem at a time... >>
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1099

Replies: 6

Tags

PoE
Related Articles
Switch suddenly disables stops delivering power to POE
1240 0
TL-SG2428P V4 does passive POE?
961 0
Poe not working on TL-SG2428P v4.0
327 0
Disabling just the POE on a port so I can plug a non poe device into my switch.
1987 0
POE port showing 100 mbps which is connected to EAP 115 accesspoint
473 0
Poe switch to poe switch
232 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.