Business Community > Switches > TL-SG1210MPE semi-bricks after 2.0 firmware upgrade
< Switches

TL-SG1210MPE semi-bricks after 2.0 firmware upgrade

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-SG1210MPE semi-bricks after 2.0 firmware upgrade

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-SG1210MPE semi-bricks after 2.0 firmware upgrade
TL-SG1210MPE semi-bricks after 2.0 firmware upgrade
2023-02-22 21:56:33
Tags: #Firmware Update
Model: TL-SG1210MPE  
Hardware Version: V2
Firmware Version: 2.0_20230219

After I flash the just-released version 2.0_20230219 of the firmware for my switch, it reboots into a recovery mode, that I can only access by accessing 192.168.0.10. There, I can re-upload version 2.0 again, after which the web GUI tells me it's fine, only to reboot back to recovery mode. If I flash version 1.0.0_20210210 of the firmware, downloaded from the same page as the newer version, everything goes back to the way it was before I started the upgrade. Could it be that the new firmware image is bad?

  0      
 
  0      
 
#1
Options
3 Reply
Re:TL-SG1210MPE semi-bricks after 2.0 firmware upgrade
2023-02-23 10:56:59

Dear @janlugt ，

 

janlugt wrote

After I flash the just-released version 2.0_20230219 of the firmware for my switch, it reboots into a recovery mode, that I can only access by accessing 192.168.0.10. There, I can re-upload version 2.0 again, after which the web GUI tells me it's fine, only to reboot back to recovery mode. If I flash version 1.0.0_20210210 of the firmware, downloaded from the same page as the newer version, everything goes back to the way it was before I started the upgrade. Could it be that the new firmware image is bad?

 

Thank you so much for taking the time to report the issue to our community!

 

1. Was there any power outage or disconnection from this switch during the update firmware version?
2. Was there a small window pop up saying" upgrade failed" during the upgrade firmware version?

3. Have you tried it with different web broswer?

4. You may backup settings and reset the switch, and try to upgrade the firmware for testing.

 

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:TL-SG1210MPE semi-bricks after 2.0 firmware upgrade
2023-02-27 13:27:39

Hi @Hank21, 

 

1. There was no power outage or disconnection during the update. I also tried twice, with the same result.

2. I did not see an 'upgrade failed' windows or popup.

3. I have only tried this with Chrome.

4. Next, I'll try a factory reset followed by an upgrade. Any browser you would recommend for this? Are there any more logs I can collect somehow?

  0  
  0  
#3
Options
Re:TL-SG1210MPE semi-bricks after 2.0 firmware upgrade
2023-02-28 12:09:39

It looks like the firmware was pulled from https://www.tp-link.com/us/support/download/tl-sg1210mpe/v2/#Firmware, I guess that means there is a problem with it? I'll await a new firmware.

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 466

Replies: 3

Tags

Firmware Update
Related Articles
TL-SG1210MPE does not respond to reboot and POE commands
385 0
 TL-SG1210MPE demo interface
472 0
 Best set-up for Ring PoE cameras with TL-SG1210MPE
434 2
ACL between VLAN and Routed Port on TL-SG3428XMP 2.0
783 0
 Issues updating firmware on a TL-SG3424P 2.0
445 0
TL-SG3428X Firmware Update not possible
1509 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.