Home

Forums

Stories

Knowledge Base

Business Community > Routers > ER7206 Policy Routing not working as expected.

< Routers

ER7206 Policy Routing not working as expected.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER7206 Policy Routing not working as expected.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Simonsen

2023-02-02 17:25:51

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-10-24

ER7206 Policy Routing not working as expected.

2023-02-02 17:25:51

Model: ER7206 (TL-ER7206)

Hardware Version: V1

Firmware Version: 1.2.3 Build 20221104 Rel.41500

I ca not get Policy Routing to work and hope the community or TP-Link can help me. I need to have the Guest network and specific MAIN IP endpoints to always use a specifc ISP, in this case ISP #1. I have created a policy routing, the IP grouping and the LAN but my traffic is still not going out to ISP #1 only?

Example of specific endpoint.

IP Group:

IP Address: EndPoint_IP, 192.168.20.51 (255.255.255.0)

IP Group: EndPoint_1, Address "Endpoint_IP"

LAN:

ID: 2, Name "Main", VLAN 20, IP Address 192.168.20.1, Subnet mask 255.255.255.0, DHCP Server "Disabled"

VLAN:

ID 2, VLAN ID 20, Name "Vlan 20", Ports 3(TAG) 4(TAG) 5(TAG), Description "MAin Network"

Policy Routing > Not Working

ID 2, Name "Endpoint_ISP1", Service Type "All", Source IP "Main", Destination IP "IPGROUP_ANY", WAN "WAN/LAN1", Effective Time "Any", Mode "Only", Status "Enabled"

What am I doing wrong?

Thanks

2 Reply

Hank21

2023-02-03 12:43:24

Posts: 3673

Helpful: 718

Solutions: 497

Stories: 8

Registered: 2021-12-13

Re:ER7206 Policy Routing not working as expected.

2023-02-03 12:43:24

Dear @Simonsen

According to your picture, the 192.168.20.1/24 network is actually created by the Deco. It's a double NAT network.

For ER7206, it can only see the Deco router WAN IP address.

A solution for you is to change the Deco as AP mode, so all networks IP will come from ER7206. However since the Deco does not support SSID VLAN ID, you will only have one main network. To use the Guest network, you can add access points like EAP225.

How to configure Multi-Networks & Multi-SSIDs on Omada SDN Controller

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*

Simonsen

LV1

2023-02-03 14:57:28

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-10-24

Re:ER7206 Policy Routing not working as expected.

2023-02-03 14:57:28

Dear @Hank21, Thank you for your reply. As far as I understand the message the ER7206 only perform Policy Routing if the networks are directly connected to the ports on the ER7206? If the networks are "virtual" and through another router such as the DECO it is not possible for the ER7206 to perform Policy Routing based on VLAN tagging? Want to make sure I understand before I start reconfigure/design my network. Thank you for your help.

ER7206 Policy Routing not working as expected.

ER7206 Policy Routing not working as expected.

Information

Voters 0

Tags