How to use ACL to create a one way VLAN

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to use ACL to create a one way VLAN

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to use ACL to create a one way VLAN
How to use ACL to create a one way VLAN
2022-10-24 00:54:19 - last edited 2022-10-24 01:01:10
Model: TL-SG3210  
Hardware Version: V2
Firmware Version: 1.9.11 Build 20150714 Rel.61832(s)

Hi there, i was wondering if anyone can help me with creating a one way VLAN? I have just recently purchased this switch and i just can not figure out the ACL settings for this. I can easily create the VLAN's so thats no problem. What i'm after is just the basic configuration on just 2 VLAN's. ( Once i got this i should be ok )

 

(VLAN 10)  ------ > (VLAN 20)

 

I would like VLAN 10 to access VLAN 20 but not for VLAN 20 to access VLAN 10.

 

* NETGEAR ProSafe™ Gigabit Dual WAN SSL VPN Firewall FVS336Gv3 *

 

I Configure the VLAN's on the Prosafe and enable DNS Proxy and Inter VLAN Routing.This is then TRUNKED to TL-SG3210 from port 4. ( If it needs to be septate ports / 2 for this i can do that )

 

* The TL-SG3210 * I Have configured VLAN 10 and VLAN 20 which are allocated septate ports on the switch.

Port 8 - Incoming from Prosafe Router (TRUNK)

Port 1 - VLAN 10 (192.168.10.1 / 24) (ACCESS) 

Port 2 - VLAN 20 (192.168.20.1 / 24) (ACCESS)

 

I can access both VLAN's and they see each other. They both have working internet access.

 

With the hole ACL section empty and in the factory default. How would i proceed?

 

Step 1?

 

Any help gratefully received. Luke 

 

 

 

 

Archer MR600 V1 3G/4G ER7212PC v1.0 TL-SG2210P v5.0 4 x EAP653(EU) v1.0
  0      
  0      
#1
Options
4 Reply
Re:How to use ACL to create a one way VLAN
2022-10-24 13:45:29

  @TazDevilLooney 

Omada Controller already update Stateful ACL(which I think can fit your requirement), however it's not available in standalone mode, also I don't know if your switch have firmware update to work with new controller verison.

  0  
  0  
#2
Options
Re:How to use ACL to create a one way VLAN
2022-10-24 14:36:05

  @Somnus 

 

Thanks for the reply Somus,

 

I have checked my current rooter and there is no ACL based settings of any kind. Am i correct that i would need to change my rooter for this to work? If thats the way to go would the (TL-R605) do the job? 

 

If i purchased a TL-R605 router and used my current TL-SG3210 V2.2 with latest firmware, it could be done?

Archer MR600 V1 3G/4G ER7212PC v1.0 TL-SG2210P v5.0 4 x EAP653(EU) v1.0
  0  
  0  
#3
Options
Re:How to use ACL to create a one way VLAN
2022-10-25 04:03:38
I'm using ER605 v1 with controller V5.6.3, however I still cannot see the new Stateful ACL option. It seems that tplink hasn't released the new firmware for this router currently. At least we know tplink will update it, since it's already on the controller release note
  0  
  0  
#4
Options
Re:How to use ACL to create a one way VLAN
2022-10-25 11:27:05

  @TazDevilLooney 

 

Would the ER7206 receive this new feature too. Does anyone know when this feature release is going to be made public? 

 

I've hit at a road block for the moment then. Was looking forward to getting that implemented. Is there any other way or any additional hardware to get this result without the wait for this new feature?    

 

Luke

Archer MR600 V1 3G/4G ER7212PC v1.0 TL-SG2210P v5.0 4 x EAP653(EU) v1.0
  0  
  0  
#5
Options