ER7206 V1 fw ER7206(UN)_V1_1.2.1 Build 20220512

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER7206 V1 fw ER7206(UN)_V1_1.2.1 Build 20220512

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER7206 V1 fw ER7206(UN)_V1_1.2.1 Build 20220512
ER7206 V1 fw ER7206(UN)_V1_1.2.1 Build 20220512
2022-07-05 06:40:09 - last edited 2022-07-05 09:17:05
Model: ER7206 (TL-ER7206)  
Hardware Version: V1
Firmware Version: ER7206(UN)_V1_1.2.1 Build 20220512

Dears,

 

we used ER5120 with many rules, 40 IP groups and in about 300 defined IP address and 3 WANs . Now we bought ER7206 V1 fw ER7206(UN)_V1_1.2.1 Build 20220512 and rewrite all ruleses and settings. Two days it was OK but third day after power down the router do not boot , only PWR LED is lighting :( There is possible hard reboot do basic configuration but after configuration restore (we have 4 version of configuration) the situation is same. After reboot the router started with PWR LED only an not working :( Have you any idea ? Can we claim router because some internal failure?

 

New knowledge: It takes 30minut to time, when SYS LED started blinking at boot continued ...  I set use port 8080 for remote admin , but it seems there some problem with authentification server ... I have to change it even if the server is disabled but have set as default 8080.. there is default period 30minute as timeout , but if I changed there was not effect for long booting ... is not acceptable 30minut for boot process :(

  0      
  0      
#1
Options
3 Reply
Re:ER7206 V1 fw ER7206(UN)_V1_1.2.1 Build 20220512
2022-07-08 06:00:40

  @PavelStudnicka 

did you mean you manually type in ips and groups into the new router? and it works for 2 days but suddenly died. and since then it takes 30 minutes to boot up?

if so, that's something new. 

did you run firmware recovery on it?

ScReW yOu gUyS. I aM GOinG hoMe. —————————————————————— For heaven's sake, can you write and describe your issue based on plain fact, common logic and a methodologic approach? Appreciate it.
  0  
  0  
#2
Options
Re:ER7206 V1 fw ER7206(UN)_V1_1.2.1 Build 20220512
2022-07-08 06:19:28 - last edited 2022-07-08 07:15:12

  @Tedd404 

Hi, I started rewrite configuration, in takes me in about 3 days . But in 2 days it was about 30% final configuration only. But if I off its and third day I on its it boots in normal 2-3 minutes time. I rewrite last block to 100% percent configuration, backuped the configuration and off the device. Fourth day I switch on it but it takes in about 30 minutes to boot :( I tried restore it from backup, but it was same. So I tried reset router do default.. it boot in normal time (2-3minute) .. but if I restored final configuration from backup once again, the boot 30 minutes was back :(  Below you can see situation ang part of log after 30min from boot when router SYS LED started blinking, ports gon UP and I can log into the admin...

 

  0  
  0  
#3
Options
Re:ER7206 V1 fw ER7206(UN)_V1_1.2.1 Build 20220512
2022-07-09 05:23:24 - last edited 2022-07-09 06:12:12

  @PavelStudnicka 

 

Yesterday I have some experiments with configuratuion and I think I found the problem. If I disabled checkbox Enable Banwidth Control, the router booted in normal time - in about 2 minutes .. but we need this function be enable :(

 

  0  
  0  
#4
Options