Omada Software Controller....not workin corretly
hi all .... I have a strange problem with omada via software and not sdn. I have router with ip 192.168.1.1 and if I connect my static pc 192.168.1.240 with open ports directly to the router omada software controller 3.4.2 also works perfectly from a mobile phone with connected access points I have installed mikrotik 4011 and since then omada no longer works, ie I regularly access omada remotely but I see unconnected access points. now the configuration is: main router: 192.168.0.1 with dmz to mikrotik 192.168.0.200 Mikrotik 192.168.1.1 and the same ports of the tim router have been opened on the mikrotik and the pc always has the same ip. so i see controller up but access points not connected. could you help me?
access point are: Eap 110 and eap 225
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Omada Controller software requires two things to work:
1. It must be able to communicate with the AP. You may try ping the EAP IP from controller PC;
2. Software uses port 29810-29814, make sure these ports are available and useable on this PC.
- Copy Link
- Report Inappropriate Content
hi mister, thanks for your help but i have still problems attached I put the screen of my omada software controller as follows: router with ip gateway 192.168.1.1 pc where omada is installed: 192.168.1.243 open doors: 29810,29811,29812,29813, 8043, and 8088. the controller points to 192.168.1.243:8043 everything works correctly even from the mobile app. now i changed pc and i installed omada again, with the following parameters: router with ip gateway 192.168.1.1 pc where omada is installed: 192.168.1.238 open doors: 29810,29811,29812,29813, 8343, and 8188. the controller points to 192.168.1.238:8343 my problem is: i did backup and restore, and also migrate site, but eap and sites have been imported, but i see disconnected devices. how can i solve my problem? I look forward to the solution. thanks always. please
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@Andrew71 I think people can't understand you.
Is your PC able to ping EAPs? Please attach ouput from ping to each EAP.
- Copy Link
- Report Inappropriate Content
Andrew71 wrote
Hi,
can you try these steps:
1) update omada software to the latest version
2) update the EAPs to the lastest firmware version
Then:
3) from the omada pc ping the EAPs
4) check if the necessary ports are reachable
Let us know how it worked out.
Marcus
- Copy Link
- Report Inappropriate Content
hi, i have tried but not resolve.
i my problem is export backup from old controller and import restore into new controller. the pc is different
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
hi mister...
thanks for your availability
i have changed all
i reset all device and i insert a new controller software.
but i have also problem
i have reset eap 235 wall
into schedule System-Controller settings i have insert the url of my controller but not adopt. i have used also omada discovery and the result is succeded, but howewer not adopt.
my settings is:
my public ip:8343 my url controller and i connect of remote.
my public ip:29810 insert into eap and into omada discovery with username and password
the port 29810 is open on tcp/udp into ip address my pc of is controller open (port forwarding on router)
i have also access from smartphone to controller, but the problem is not adopting the device.
how i ping commands to each EAP from new Omada controller PC?
why is not adopt?
- Copy Link
- Report Inappropriate Content
hi all the forum
i have a question...
i have installed Oc200 Omada Sdn Controller
if i used IP:port for access to controller, the software omada i can delete?
the controller i ping also remote access
one problem:
which port i open for adopt device to remote?
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 958
Replies: 10
Voters 0
No one has voted for it yet.