connect switch TL-SG1024DE with L3 switch using trunking 2 ports
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
hi, i have network in combination the l3 switch and the l2 switches. my l2 switches are connected on l3 switch trunking 2 ports. the l3 switch is allied telesis x510-52gtx. the l2 switches are cisco catalyst 2960 24port. i have not experience with tp-link switches? how i connect TL-SG1024DE in my netwok per same system?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
configuration 2 ports on l3 switch is:
interface port1.0.9-1.0.10
description VIII_Sprat
switchport switchport mode trunk
switchport trunk allowed vlan add 5-7,80-83
channel-group 5 mode active
access-group ip_range_list
on my l2 tp link switch are vlan's 5-7,80-83
- Copy Link
- Report Inappropriate Content
On your tplink switch, set the port you're gonna have a connect to the L3 switch, VLAN ID 5-7 and 80-83, tagged. Then, your L3 switch can talk to the TP switch. That port you configed on the TP switch is a trunk port.
A guide for you to tag on your switch: https://www.tp-link.com/us/support/faq/788/
- Copy Link
- Report Inappropriate Content
@John1234 on my l3 switch is configured trunking for 2 ports that go to ports 1,2 on tp link.those ports on tp link must be trunked? I configured tp link switch but my configuration does not works
- Copy Link
- Report Inappropriate Content
configuration trunk ports on the l3 switch is below
interface port1.0.9-1.0.10
description VIII_Sprat
switchport
switchport mode trunk
switchport trunk allowed vlan add 5-7,80-83
channel-group 5 mode active
access-group ip_range_list
on the tp link sg-1024 i created two ports in trunk and i set them untagged in vlan 80, i created for testing ports 3 and 4 in vlan 80 tagged, i set pvid 80 for ports 3,4 and pvid 1 for ports 1 and 2, but my configuration does not works. when workstation connect on port 3 i don't receive ip address from my dhcp server which in another vlan 99 that there's on the l3 switch
- Copy Link
- Report Inappropriate Content
i have concluded that the configuration of my l3 switch is configured with trunking, so two ports on the l3 switch does not support the link aggregation of tp-sg1024de. can you give me some guide how reconfigure my the l3 switch. the configuration LACP on my l3 switch is
lacp global-passive-mode enable
lacp system-priority 1
interface port1.0.9-1.0.10
description VIII_Sprat
switchport
switchport mode trunk
switchport trunk allowed v
channel-group 5 mode active
access-group ip_range_list
sflow sampling-rate 512
sflow polling-interval 60
interface po5
description VIII_Sprat
switchport
switchport mode trunk
switchport trunk allowed vlan add 5-7,80-83
- Copy Link
- Report Inappropriate Content
I am sorry that I don't understand your expression.
I'll give the example and you modify your settings according to your need. VLAN is about tagging/untagging and VLAN IDs.
So, L3 switch, let's call it L3. TP switch, TP.
On your L3, there is a port, that'll be used for connection to the TP. e.g. port #10
Port #10 should be a tagged port with the following VLAN IDs: 5-7 80-83. Whatever the ID you need.
Then, check your TP, the port you used for the connection. Let's say port #2
Port #2 should be a tagged port with the following VLAN IDs 5-7 80-83.
So you see? They match with each other. There will be VLAN 5-7 80-83 between the L3 and TP.
If you don't have the VLAN IDs configured on TP and L3, you won't get matching VLANs.
One single port is enough for multiple VLAN IDs. What's the point to get two ports?? Two on L3 and two on TP for the connection?
PVID is for untagged ports. If your ports are tagged, no need to use PVID.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1422
Replies: 6
Voters 0
No one has voted for it yet.