OC200 latest firmware update fails
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
I have now doen this process twice, and both times failed exactly the same.
Performing the upgrade to the new firmware (5.x) from the last latest release (September 21) fails. After reboot it gets to 67% at start up and just sits there indefinately with no clue as to what its doing - left it for an hour or so!.
Power cycle it and then it states abnormal data has been detected.
Factory reset and then it boots, then try to restore the backed up config which gets to 98% and fails to play.
Really not helpful, now to downgrade the thing again !.
This update seems a fail on my part !!.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I can confirm that it now also worked for me on the first attempt after I had briefly deactivated Cloud Access for the upgrade and executed the upgrade locally directly on the OC200.
- Copy Link
- Report Inappropriate Content
The cause for me was down to having a portal setup but disabled. Deleted that at TP-links advice and the update has now taken.
I think there will be another firmware update in the near future to catch some of these strange issues.
Hopefully we are all getting it working now one way or another.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Auto backup does require PoE as the power source. Performing an update locally is always recommended. supermarket was right about the update. Download, unzip, upload manually, keep the power and connection for the whole process.
I heard doing auto upgrades to the devices and upgrading OC200 at the same time. The Poe switch power cycled because of the upgrade. And OC200 was using Poe. Booom, OC200 bricked because of loss of power during the update.
- Copy Link
- Report Inappropriate Content
PSA: It looks like they've just posted an updated firmware to 5.0.30, which addresses the issue:
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Dear @JhonneL,
JhonneL wrote
in 100% experience my main live controller where 19units eap 225 outdoor are mesh connected always corrupted in my more than 1 year experience updating oc200 v1 controller. but in process of bsame procedure for my backup controller oc200 v1 (no eap's connected or active) 100% success hheghe, weird might this firmware process are regular failed in live active environment always @fae help pls,
The issue you are experiencing sounds unusual, I'd like to escalate your case to the TP-Link support team for further investigation.
They will reach you via your registered email address shortly, please pay attention to your email box later.
Once the issue is addressed or resolved, I'd encourage you to share it with the community.
Thank you so much for your cooperation and patience!
- Copy Link
- Report Inappropriate Content
@Fae Thank you I been in e-mail communication now with Hugh from TPLINK support team for the escalated known issue in my case.
Best Regards.
Fae wrote
Dear @JhonneL,
JhonneL wrote
in 100% experience my main live controller where 19units eap 225 outdoor are mesh connected always corrupted in my more than 1 year experience updating oc200 v1 controller. but in process of bsame procedure for my backup controller oc200 v1 (no eap's connected or active) 100% success hheghe, weird might this firmware process are regular failed in live active environment always @fae help pls,
The issue you are experiencing sounds unusual, I'd like to escalate your case to the TP-Link support team for further investigation.
They will reach you via your registered email address shortly, please pay attention to your email box later.
Once the issue is addressed or resolved, I'd encourage you to share it with the community.
Thank you so much for your cooperation and patience!
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 8437
Replies: 39
Voters 0
No one has voted for it yet.