Omada SDN 5.0.15 Bug report And now 5.0.29
WiFi traffic distribution is empty, speed test fails and gateway is not available, I mean we have had the same error on previous versions,
There are ER605 routers on this controller. applies to all sites except default on which there are no devices.
Again, why does tp-link not have a beta program, now we are beta testers in release version again. this error we would have easily avoided if we could test first. I was stupid enough to install on a server with two site before I tested.
There was also problem with mongo db ports and i have to complete uninstall omada from computer and install a new omada server, then restore from backup to get it to work.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
The new controller 5.0.29 use TCP port 29814 for adoption, this have to be NATed in firewall in remote site.
this is not mention in release note in windows controller only in OC200 release note.
More information about the new port
https://www.tp-link.com/no/support/faq/3265/
- Copy Link
- Report Inappropriate Content
I did as I should have done in the first place.
Installed a new server in lab environment, installed omada controller ver 4.4.6 imported a test site, upgraded to omada controller 5.0.15, but I get exactly the same error except Wi-Fi Traffic Distribution..
- Copy Link
- Report Inappropriate Content
Dear @shberge,
shberge wrote
I did as I should have done in the first place.
Installed a new server in lab environment, installed omada controller ver 4.4.6 imported a test site, upgraded to omada controller 5.0.15, but I get exactly the same error except Wi-Fi Traffic Distribution..
The Controller v5.0.15 and ER605 V1 1.1.1 have been running in our lab for two days or so, no "General Error" occurs, everything works as expected without any issues.
For your case, would the "General Error" only occur after you try to run a speed test on the Dashboard?
Could you please check the running log and see if there is something special? What's the Java version you are running with?
- Copy Link
- Report Inappropriate Content
Fae wrote
Dear @shberge,
For your case, would the "General Error" only occur after you try to run a speed test on the Dashboard?
Could you please check the running log and see if there is something special? What's the Java version you are running with?
Yes the General error was there before and after speed test, I use java jre-8u311-windows-x64 on the computer.
I remember similar error on earlier version and then we have to do som spedtest and enable periodic spedeed test..
What should i lok after in running log??
I have now done two installation with same result, one is reverted back and my lab steel with newest version
Anyhow, Error like this this give me a lot of trouble, I have to downgrade on server yesterday and downgrade don't work very wel. when downgrade server and restore latest backup all device com up with managed by other or something like that. when i adopt this device with username and password then all setting was gone on all device, router, access point and switch. vpn no-ip and so on was gone.
- Copy Link
- Report Inappropriate Content
Dear @shberge,
shberge wrote
Yes the General error was there before and after speed test, I use java jre-8u311-windows-x64 on the computer.
I remember similar error on earlier version and then we have to do som spedtest and enable periodic spedeed test..
What should i lok after in running log??
I have now done two installation with same result, one is reverted back and my lab steel with newest version
Anyhow, Error like this this give me a lot of trouble, I have to downgrade on server yesterday and downgrade don't work very wel. when downgrade server and restore latest backup all device com up with managed by other or something like that. when i adopt this device with username and password then all setting was gone on all device, router, access point and switch. vpn no-ip and so on was gone.
Sorry to hear that you have a lot of trouble with the controller.
The issue you are experiencing sounds unusual, I'd like to escalate your case to the TP-Link support team for further investigation.
They will reach you via your registered email address shortly, please pay attention to your email box later.
Once the issue is addressed or resolved, I'd encourage you to share it with the community.
Thank you so much for your cooperation and support!
- Copy Link
- Report Inappropriate Content
i would like to try on ubuntu, do you have any deb file for ubuntu available for testing for the new controller software. my plan is anyway to migrate over to this platform for all device.
Fae wrote
Dear @shberge,
shberge wrote
Yes the General error was there before and after speed test, I use java jre-8u311-windows-x64 on the computer.
I remember similar error on earlier version and then we have to do som spedtest and enable periodic spedeed test..
What should i lok after in running log??
I have now done two installation with same result, one is reverted back and my lab steel with newest version
Anyhow, Error like this this give me a lot of trouble, I have to downgrade on server yesterday and downgrade don't work very wel. when downgrade server and restore latest backup all device com up with managed by other or something like that. when i adopt this device with username and password then all setting was gone on all device, router, access point and switch. vpn no-ip and so on was gone.
Sorry to hear that you have a lot of trouble with the controller.
The issue you are experiencing sounds unusual, I'd like to escalate your case to the TP-Link support team for further investigation.
They will reach you via your registered email address shortly, please pay attention to your email box later.
Once the issue is addressed or resolved, I'd encourage you to share it with the community.
Thank you so much for your cooperation and support!
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
To be honest. this was not expected.
fortunately I only test in LAB environment
installed a new Windows controller v 5.0.29 and adopted a router and switch without any problems, but EAP245v3 can not be adopted.
i have reset to deafult and tried a lot of different but no.
This is a remote controller on a different LAN than the devices but this is usually not a problem.
I do som more test and this really suprise me, How do tp-link test software ??
all whit latest aviable software
EAP225-Outdoor IS OK adopt with no issue
EAP620HDv1 adopt failed
EAP660HDv1 adopt failed
EAP245v3 adopt failed
if I downgrade EAP245v3 to 5.0.3 its OK adopt with no issue
The new EAP software destroy adopt url on access point, url is changed from my.remote.site:29810 to my.remote.site?dPort=29810&mPort=0&omadacId=c21f969b5f03d33d43e04f8f136e7682
EDIT
I do a downgrade to 1.0.6 on EAP620HDv1 and after downgrade it adopt with no issue.
- Copy Link
- Report Inappropriate Content
The new controller 5.0.29 use TCP port 29814 for adoption, this have to be NATed in firewall in remote site.
this is not mention in release note in windows controller only in OC200 release note.
More information about the new port
https://www.tp-link.com/no/support/faq/3265/
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2353
Replies: 8
Voters 0
No one has voted for it yet.