Business Community > WiFi > TP-Link Omada EAP245 V3
< WiFi

TP-Link Omada EAP245 V3

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TP-Link Omada EAP245 V3

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TP-Link Omada EAP245 V3
TP-Link Omada EAP245 V3
2021-10-12 12:51:01 - last edited 2021-10-13 06:56:58
Model: EAP245  
Hardware Version: V3
Firmware Version:

Hey,

 

I'm having a small issue with one of my TP-Link Omada EAP245 V3TP-Link Omada EAP245 V3 Access Points.

 

After an electricity failure (connected via POE to my switch) I had to reset this one Access Point, out of a set of 5 - managed by Omada.

Then I've set an username and password again and added it again to Omada with all the correct settings, which are managed by the "site".

 

However the Access Point keeps blinking: 4 seconds green - 1 second nothing; over and over again.

In Omada everything seems fine.

 

What is the reason for this blinking? Is it because currently no clients are connected to the Access Point?

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:TP-Link Omada EAP245 V3-Solution
2021-10-12 16:09:03 - last edited 2021-10-13 06:56:58

Found and solved the issue!

 

For some reason the IP address for my gateway (router) was saved into the Primary DNS, and thus no gateway address was set.

 

Just blanked the Primary Address and moved it to Gateway and all works now!

 

So some sort of isolation indeed, but not seen as such by the Controller.

Recommended Solution
  1  
  1  
#6
Options
5 Reply
Re:TP-Link Omada EAP245 V3
2021-10-12 14:03:35 - last edited 2021-10-13 06:56:58

@Threesa 

 

Check this post for details.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:TP-Link Omada EAP245 V3
2021-10-12 14:16:21 - last edited 2021-10-13 06:56:58

@terziyski  As I've already reset and reconnected the device it doesn't really answer my question.

Hence my topic. I had seen that topic indeed.

  0  
  0  
#3
Options
Re:TP-Link Omada EAP245 V3
2021-10-12 15:17:23 - last edited 2021-10-13 06:56:58

@Threesa 

 

That was the closest description to your LED state I've seen.

From EAP245's installation guide the "flashing green slowly" means that the EAP is in isolated state.

If that's the case you can check the following solution.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#4
Options
Re:TP-Link Omada EAP245 V3
2021-10-12 15:46:41 - last edited 2021-10-13 06:56:58

@terziyski 

 

Doesn't seem to be in isolated mode neither.

Shouldn't it be solid yellow then as well?

  0  
  0  
#5
Options
Re:TP-Link Omada EAP245 V3-Solution
2021-10-12 16:09:03 - last edited 2021-10-13 06:56:58

Found and solved the issue!

 

For some reason the IP address for my gateway (router) was saved into the Primary DNS, and thus no gateway address was set.

 

Just blanked the Primary Address and moved it to Gateway and all works now!

 

So some sort of isolation indeed, but not seen as such by the Controller.

Recommended Solution
  1  
  1  
#6
Options

Information

Helpful: 0

Views: 2071

Replies: 5

Related Articles
Does EAP245 v3 support Omada mesh?
527 0
TP-Link EAP245 V3 at a church
591 0
EAP245 V3 from Amazon
887 0
Omada Discovery Utility cannot find the EAP245 V3
2867 0
EAP245 V3 TCPDUMP inquiry
885 0
EAP245 v3 :: 5GHz channels
2346 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.