Business Community > Controllers > Omada OC200 can't adopt TL-SG3428 v2.0 password fail
< Controllers

Omada OC200 can't adopt TL-SG3428 v2.0 password fail

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Omada OC200 can't adopt TL-SG3428 v2.0 password fail

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Omada OC200 can't adopt TL-SG3428 v2.0 password fail
Omada OC200 can't adopt TL-SG3428 v2.0 password fail
2021-08-11 23:14:45 - last edited 2021-08-11 23:45:45
Model: OC200  
Hardware Version: V1
Firmware Version: 1.8.0 Build 20210406 Rel.58757

I had to reset my equipment and now my 24 port switch (TL-SG3428) will not be adopted by the controller. It fails on password even though I have tried both the default user name and password and the password that was setup with it.  How do I reset this switch? The documentation is not clear on how to do this other than pluggin in a usb cable to it. Can I do it with a mac or does it have to be a windows machine using putty? Still need the steps involved to reset this.

 

Help needed.

 

 

Thanks

  0      
 
  0      
 
#1
Options
4 Reply
Re:Omada OC200 can't adopt TL-SG3428 v2.0 password fail
2021-08-12 00:05:48 - last edited 2021-08-12 00:14:01

@gargantua 

 

If the device can be detected by the controller, you can reset it from the controller. Go to Devices-->click the switch-->Config--->Manage device--->Forget:

  0  
  0  
#2
Options
Re:Omada OC200 can't adopt TL-SG3428 v2.0 password fail
2021-08-12 00:26:30

@gargantua It's not adoptable so not configurable. 

 

  0  
  0  
#3
Options
Re:Omada OC200 can't adopt TL-SG3428 v2.0 password fail
2021-08-12 00:54:30

@gargantua 

 

Oh sorry, as my devices are all connected, so I didn't realize this page. But I think you can try to log in to the switch's web interface via the password you set or the default password. If you can get into it, you can reset from the web interface. If both passwords are incorrect, I think you must use PuTTy on Windows to reset it because there is only Windows driver.

Here is a guide for you:

https://www.tp-link.com/en/support/faq/3146/

  0  
  0  
#4
Options
Re:Omada OC200 can't adopt TL-SG3428 v2.0 password fail
2021-08-13 02:40:19

Dear @gargantua,

 

gargantua wrote

How do I reset this switch? The documentation is not clear on how to do this other than pluggin in a usb cable to it. Can I do it with a mac or does it have to be a windows machine using putty? Still need the steps involved to reset this.

 

Except for the FAQ guide pointed out by @Somnus, you may check the following post for more detailed guidance.

 

How to enter the BootUtil menu to reset TP-Link Managed Switch via Console Port?

 

If the issue is resolved, I'd encourage you to share it with the community.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 2673

Replies: 4

Related Articles
Firmware update - TL-SG3428 v2.0
720 0
Can't get Omada OC200 Controller to adopt EAP225(EU)v2
476 0
Omada OC200 and TL-R605
1961 0
TL-R605 can't adopt
17891 1
"Un-adopt" a router from OC-200?
1863 0
Link flapping on TL-SG3428 v2.0 with client device
589 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.