Home

Forums

Stories

Knowledge Base

Business Community > Switches > ACL not work, BUG on TL-SG3428 V2

< Switches

ACL not work, BUG on TL-SG3428 V2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ACL not work, BUG on TL-SG3428 V2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MGergely

2021-07-06 22:01:30 - last edited 2022-09-01 02:40:47

Posts: 8

Helpful: 12

Solutions: 0

Stories: 0

Registered: 2021-06-24

ACL not work, BUG on TL-SG3428 V2

2021-07-06 22:01:30 - last edited 2022-09-01 02:40:47

Model: TL-SG3428

Hardware Version: V2

Firmware Version: 2.0.3 Build 20210409 Rel.52950

I tried to create an ACL entry to block a port (TCP 8888) on an IP address (10.10.10.10/32) (because it also not blocked/controlled via the router: ER7206 (TL-ER7206) )

I applied that on all port (or all VLAN) of the switch, but that IP on specific port is still accessible. Settings (only this ACL setting exist on that switch, no other rule or ACL):

1 Accepted Solution

Fae

2022-09-01 02:39:58 - last edited 2022-09-01 02:40:02

Posts: 3613

Helpful: 1357

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:ACL not work, BUG on TL-SG3428 V2-Solution

2022-09-01 02:39:58 - last edited 2022-09-01 02:40:02

Hi there,

The new firmware TL-SG3428(UN)_V2_2.0.7 Build 20220606 released recently has fixed the ACL-related issue.

If you find that Combined ACL failed to block traffic between Layer 3 networks, please check for a firmware update first.

Thank you for your attention!

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

2 Reply

MGergely

LV1

2021-07-10 13:29:29 - last edited 2021-07-10 13:31:30

Posts: 8

Helpful: 12

Solutions: 0

Stories: 0

Registered: 2021-06-24

Re:ACL not work, BUG on TL-SG3428 V2

2021-07-10 13:29:29 - last edited 2021-07-10 13:31:30

@MGergely I tried a Phone call and e-mail about that, but not answered... ACL not work so I also can't block traffics between VLANs...

Fae

2022-09-01 02:39:58 - last edited 2022-09-01 02:40:02

Posts: 3613

Helpful: 1357

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:ACL not work, BUG on TL-SG3428 V2-Solution

2022-09-01 02:39:58 - last edited 2022-09-01 02:40:02

Hi there,

The new firmware TL-SG3428(UN)_V2_2.0.7 Build 20220606 released recently has fixed the ACL-related issue.

If you find that Combined ACL failed to block traffic between Layer 3 networks, please check for a firmware update first.

Thank you for your attention!

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

ACL not work, BUG on TL-SG3428 V2

ACL not work, BUG on TL-SG3428 V2

Information

Voters 1

Tags