Eap225 not adopt remote controller

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Eap225 not adopt remote controller

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Eap225 not adopt remote controller
Eap225 not adopt remote controller
2021-06-20 20:47:54
Model: EAP225-Outdoor  
Hardware Version: V1
Firmware Version:

hi all, i have a problem with 2 eap 225....i am on my client and i cannot adopt eap on my controller that find on my office....i have also cloud but not resolve....it's possible help me?

  0      
  0      
#1
Options
6 Reply
Re:Eap225 not adopt remote controller
2021-06-21 01:00:02

@Andrew71 

 

Hey

 

Did you mention the controller in the office.. are the EAPs in a different location?    If so you need to have connectivity to the office to allow adoption, this can be via a VLAN or tunnel between the office router and the remote router where the EAPs are located

 

 

  0  
  0  
#2
Options
Re:Eap225 not adopt remote controller
2021-06-21 16:56:46

@Philbert 

 

yes my friends.... i speak about...

i am at your home and you have a eap 225 outdoor.... i have a controller to my office and i want add your eap 225 for management on my controller. i used discovery tool and insert when adopting:

Ip static of my office

login and password of eap

 

the message is adotped success, but i don't find on my controller.

 

i wrong?

 

i wait your helpm and greatfully

  0  
  0  
#3
Options
Re:Eap225 not adopt remote controller
2021-06-22 07:59:09

@Andrew71 

What is your Controller version? What is the firmware version of your EAP? Please make sure it's not a compatible problem.

 

Moreover, you have to set port forwarding for your Controller, on your Router/Modem Router which the Controller is connecting to, open TCP&UDP port for your Controller, ranging from 29810 to 29813.

For your reference, here is the Guide,

How to manage EAPs at different places across internet using Omada Controller (via NAT Port Forwarding and EAP Discovery Utility)? (New UI)

 

 

Just striving to develop myself while helping others.
  2  
  2  
#4
Options
Re:Eap225 not adopt remote controller
2021-06-27 14:21:45 - last edited 2021-06-27 14:23:45

@Virgo 

 

my controller is 3.2.14, and firmware on eap 225 outdoor is v1...it's possible??? i cannot resolve? i have open port of omada controller and i access from remote to my controller, but when i am to client i cannot add eap....only local

  0  
  0  
#5
Options
Re:Eap225 not adopt remote controller
2021-06-28 23:44:10 - last edited 2021-06-28 23:46:05

@Andrew71 

 

V1 is the hardware version, not the firmware, and if the Controller is V3.2.14, the firmware or your EAP should be 

 

and you can also try to disable the firewall on PC for a test.

Just striving to develop myself while helping others.
  0  
  0  
#6
Options
Re:Eap225 not adopt remote controller
2021-07-09 07:14:02

Dear @Andrew71,

 

Andrew71 wrote

my controller is 3.2.14, and firmware on eap 225 outdoor is v1...it's possible??? i cannot resolve? i have open port of omada controller and i access from remote to my controller, but when i am to client i cannot add eap....only local

 

Kind note that the current EAP225-Outdoor firmware listed on the TP-Link website is almost for Omada Controller V4 or above.

 

To fully work with Omada Controller v3.2.14, you may check the firmware version(the Build number) of your EAP225-Outdoor, which can be found via the discovery utility. If the current firmware is compatible with Controller v4 or above, you may refer to this post to downgrade the firmware of your EAP225-Outdoor and see if it helps.

 

If your concern is resolved, I'd encourage you to give feedback to the community so others can be confident of the solution.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#7
Options