Switch TL-SG2008P no statistic after upgrade fw
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello,
statistics for devices connected to the LAN switch have stopped being recorded after firmware update.
The network has a topology:
TL-R605 v1.0 1.0.1 Build 20210113 Rel.35074
TL-SG2008P v1.0 1.0.1 Build 20210407 Rel.54710
1. switch port - EAP245(EU) v3.0 5.0.2 Build 20210303 Rel. 34713
2. switch port - EAP225-Outdoor(EU) v1.0 5.0.3 Build 20210316 Rel. 67358
3. switch port - OC200 1.0 20210406 Rel.58757 con.ver. 4.3.5
next switch port TV, NAS, PC.
Thank for fix,
Pavel
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Running 1.0.1 on TL-SG2008P and doing speedtests with a 1Gbps up and down connection freezes on the upload test and disconnects other users from network, completely bogs the network down.
When reverted back to 1.0.0, speedtests run smooth and normally without interfering with the rest of the network.
Topology:
CenturyLink Fiber ONT
--
TL-R605
--
TL-SG2008P
--
Wired Connections
--
EAP245
--
Wireless Connections
If I run 1.0.1 and I plug everything into the LAN ports on the TL-R605 the speedtests run normal when they are ran through the gateway.
Just the TL-SG2008P 1.0.1 firmware.
It had me thinking I had faulty hardware at first so I had ordered a replacement on Amazon before figuring out that it was the firmware by downgrading it back to 1.0.0
I hope there is a fix soon.
- Copy Link
- Report Inappropriate Content
@710james best to open a new thread since this is a different issue to the one covered in this thread
- Copy Link
- Report Inappropriate Content
@bdl perhaps I will seeing as this is one of two threads mentioning the TL-SG2008P.
- Copy Link
- Report Inappropriate Content
This issue is also present on the TL-SG3428MPv1.0 with firmware 1.0.1.
This issue is NOT present on the TL-SG3428v2.0 with firmware 2.0.3.
I am also looking forward to working firmware.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I had this issue and I found the fw beta link and applied successfully into OC200 and SG2008P switches. Apparently, the statistics problem is gone and they are running fine so far.
I am using OC200, SG2008P and a AP with latest FW with VLANs. Infra looking good. Waiting for my router arrive to complete my set up. Cheers
- Copy Link
- Report Inappropriate Content
After installing Firmware Version: 1.0.1 Build 20210604 Rel.36558(Beta) on Model: TL-SG2210MP v1.0 the traffic statistics are working however POE status and budget are not reporting any data.
Please see attached screenshot for more info. Port 2 of the SG2210MP is uplinked to a EAP225 and should show POE in use and about 5 watts of the budget used.
- Copy Link
- Report Inappropriate Content
Dear @warllo,
warllo wrote
After installing Firmware Version: 1.0.1 Build 20210604 Rel.36558(Beta) on Model: TL-SG2210MP v1.0 the traffic statistics are working however POE status and budget are not reporting any data.
Please see attached screenshot for more info. Port 2 of the SG2210MP is uplinked to a EAP225 and should show POE in use and about 5 watts of the budget used.
Do you mean the PoE status and budget are showing up properly before you install the Beta firmware?
If you plug the EAP to other ports on the switch, would it make any difference?
- Copy Link
- Report Inappropriate Content
Before upgrading to the beta firmware the poe budget and status was reporting correctly. Post upgrade to the beta firmware the poe budget and status are not working correctly. Moving to a different port does not have any affect.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 14421
Replies: 61
Voters 0
No one has voted for it yet.