Business Community > Controllers > Omada 4.2.8 can't adopt EAP225-Outdoor wireless but ok if connected with ethernet cable
< Controllers

Omada 4.2.8 can't adopt EAP225-Outdoor wireless but ok if connected with ethernet cable

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Omada 4.2.8 can't adopt EAP225-Outdoor wireless but ok if connected with ethernet cable

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Omada 4.2.8 can't adopt EAP225-Outdoor wireless but ok if connected with ethernet cable
Omada 4.2.8 can't adopt EAP225-Outdoor wireless but ok if connected with ethernet cable
2021-01-12 16:58:36 - last edited 2021-01-13 14:12:26

Hello, 

 

I am trying to add a EAP225-Outdoor AP to an existing EAP225 V3 wired using mesh functionality. Omada version is 4.2.8 on Linux. When I connect the ethernet cable, I can provision it without issue.

 

The error is Adopt Failed. If I try again it ask for a different password. I tried the default one (admin/admin) and the current one for the other AP. After a few try, I get a No available uplink AP error. At this point I can't go further.

 

I reseted the AP many time (the outdoor one) wihtout success. I also try to provision it via ethernet, forget it, replug it without success.

 

Mesh funcitonnality is activated. I also checked the Channel Limit function.

 

I am using a Management VLAN and static IPs (maybe this cause problems??)

 

Thank You for your suggestion

 

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Omada 4.2.8 can't adopt EAP225-Outdoor wireless but ok if connected with ethernet cable-Solution
2021-01-13 08:02:11 - last edited 2021-01-13 14:12:26

Dear @EtRod_,

 

Please check the channel on the root EAP225, ensure it's supported by the EAP225-Outdoor.

For more details, please check this post.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#3
Options
3 Reply
Re:Omada 4.2.8 can't adopt EAP225-Outdoor wireless but ok if connected with ethernet cable
2021-01-12 17:24:48

Ok I went a little further this time. 

 

I tried a suggestion found in another post. 

 

I provisionned it on ethernet, then disconnected ethernet et reboot the AP. The AP then went in isolated state. From there I try to link to the other AP using the Mesh menu but it failed

  0  
  0  
#2
Options
Re:Omada 4.2.8 can't adopt EAP225-Outdoor wireless but ok if connected with ethernet cable-Solution
2021-01-13 08:02:11 - last edited 2021-01-13 14:12:26

Dear @EtRod_,

 

Please check the channel on the root EAP225, ensure it's supported by the EAP225-Outdoor.

For more details, please check this post.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#3
Options
Re:Omada 4.2.8 can't adopt EAP225-Outdoor wireless but ok if connected with ethernet cable
2021-01-13 14:11:51

@Fae 

 

That was it... There should be an option to limit channel to regulatory channels in MESH mode for all AP not only Outdoor one...

 

Thank You very much

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 1511

Replies: 3

Related Articles
Adopt loop with EAP225-Outdoor
460 0
Can't get Omada OC200 Controller to adopt EAP225(EU)v2
476 0
eap225-outdoor won't adopt via wireless but works fine hardwired
959 0
Can't connect CPE710 to EAP225-Outdoor
677 0
 Cant adopt first EAP225-outdoor
346 0
 On EAP225-Outdoor adption, i Can't connect to wireless network
252 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.