Business Community > Controllers > T1500G-8T v2.0 create LACP bonds on Omada
< Controllers

T1500G-8T v2.0 create LACP bonds on Omada

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

T1500G-8T v2.0 create LACP bonds on Omada

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
T1500G-8T v2.0 create LACP bonds on Omada
T1500G-8T v2.0 create LACP bonds on Omada
2020-12-18 16:17:57 - last edited 2021-05-24 08:06:36
Model: T1500G-8T(TL-SG2008)  
Hardware Version: V2
Firmware Version: 2.0.6

Hi 

 

I'm trying to create a LACP with 4 ports in a T1500G-8T v2.0 switch that is managed by Omada 4.24. 

 

It doesn't give an option to do it or I couldn't find where it is. Am I missing where it is or do I have to remove it from Omada's ?

 

THanks

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:T1500G-8T v2.0 create LACP bonds on Omada-Solution
2021-01-06 19:35:31 - last edited 2021-05-24 08:06:36
That's because you are in batch edit mode. Select only one of the ports you want to have in the LAG and you will get the option in the override menu. There you can select all the ports that should be part of the LAG. The software isn't this intuitive here. Kind regards Martin
Recommended Solution
  1  
  1  
#7
Options
4 Reply
Re:T1500G-8T v2.0 create LACP bonds on Omada
2020-12-23 02:57:13

Dear @AndreMartins,

 

I'm trying to create a LACP with 4 ports in a T1500G-8T v2.0 switch that is managed by Omada 4.24. 

It doesn't give an option to do it or I couldn't find where it is. Am I missing where it is or do I have to remove it from Omada's ?

 

LACP is under the LAN Network part.

 

 

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  1  
  1  
#2
Options
Re:T1500G-8T v2.0 create LACP bonds on Omada
2020-12-28 18:20:45 - last edited 2020-12-28 18:23:15

@AndreMartins 

 

Hi Fae

 

I'm using Oada 4.28 now and my T1500G-8T v2 is running 2.0.6 Build 20200805 Rel.56922 

 

I don't have aggregatte when I try to override the profile. I also tried to create a new profile and it doesn't show there either.

 

I can do it when it is not connected to Omada. 

 

  0  
  0  
#3
Options
Re:T1500G-8T v2.0 create LACP bonds on Omada-Solution
2021-01-06 19:35:31 - last edited 2021-05-24 08:06:36
That's because you are in batch edit mode. Select only one of the ports you want to have in the LAG and you will get the option in the override menu. There you can select all the ports that should be part of the LAG. The software isn't this intuitive here. Kind regards Martin
Recommended Solution
  1  
  1  
#7
Options
Re:T1500G-8T v2.0 create LACP bonds on Omada
2021-01-07 13:46:56

@mwo 

 

Thanks, it did work now.

  0  
  0  
#8
Options

Information

Helpful: 0

Views: 2953

Replies: 4

Related Articles
 T1500G-8T v2.0 LACP Layer3+4
564 0
Firmware upgrade on T1500G-8T v2
1440 0
 Enable Jumbo Packets on T1500G-8T v2.0 connected to Omada
937 0
Upgrade Firmare on T1500G-8T(TL-SG2008)
2063 0
 Bonding questions for T1500G-8T
492 0
 T1500G-8T. Can't access configuration
667 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.