Business Community > Controllers > 802.11 Data Rate Control settings
< Controllers

802.11 Data Rate Control settings

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

802.11 Data Rate Control settings

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
802.11 Data Rate Control settings
802.11 Data Rate Control settings
2020-12-04 14:07:22 - last edited 2020-12-08 07:38:52
Model: Omada Software Controller (Windows)  
Hardware Version: V1
Firmware Version: 4.2.4

 

Good day,

i just want to know your opinion guys on this matter.. 

i have these settings and notice an improvement on the 5ghz band and i am curious what is the proper setting for the 2.4ghz band as i feel no changes ever happened.

 

settings: (minimum data rate control)

2.4ghz band is set to 6mbps

5ghz band is set to 9mbps

 

also should i put checkmarks on the "send beacon" and "disable CCK rates"?

 

thanks in advance..

 

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:802.11 Rate Control settings-Solution
2020-12-07 08:56:13 - last edited 2020-12-08 07:38:52

Dear @totin1227,

 

i have these settings and notice an improvement on the 5ghz band and i am curious what is the proper setting for the 2.4ghz band as i feel no changes ever happened.

settings: (minimum data rate control)

2.4ghz band is set to 6mbps

5ghz band is set to 9mbps

 

also should i put checkmarks on the "send beacon" and "disable CCK rates"?

 

The 802.11 Rate Control can only help to improve network performance in a high-density network. 

 

You can tick the "Disable CCK Rates" box to disable the CCK data rates (1/2/5.5/11 Mbps) for checking, if there are old 2.4GHz devices in your network, it may improve the 2.4GHz performance in your network. If there are multiple SSIDs configured in your network, you can also tick the "send beacon" option to have a try.

 

Similar discussion regard with the 802.11 Rate Control can be found here.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
3 Reply
Re:802.11 Rate Control settings-Solution
2020-12-07 08:56:13 - last edited 2020-12-08 07:38:52

Dear @totin1227,

 

i have these settings and notice an improvement on the 5ghz band and i am curious what is the proper setting for the 2.4ghz band as i feel no changes ever happened.

settings: (minimum data rate control)

2.4ghz band is set to 6mbps

5ghz band is set to 9mbps

 

also should i put checkmarks on the "send beacon" and "disable CCK rates"?

 

The 802.11 Rate Control can only help to improve network performance in a high-density network. 

 

You can tick the "Disable CCK Rates" box to disable the CCK data rates (1/2/5.5/11 Mbps) for checking, if there are old 2.4GHz devices in your network, it may improve the 2.4GHz performance in your network. If there are multiple SSIDs configured in your network, you can also tick the "send beacon" option to have a try.

 

Similar discussion regard with the 802.11 Rate Control can be found here.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
Re:802.11 Rate Control settings
2020-12-07 23:49:09

@Fae 

 

Thanks for the reply. 

 

I would give your recommendations a try and see what happens, especially on the "send beacon" as i have 2 SSID's. Also going through the link for a read. 

 

Again thanks 🙂

  0  
  0  
#3
Options
Re:802.11 Rate Control settings
2020-12-20 22:55:38

@Fae Can you explain if this is supposed to only impact TX rate? I have mine set to 36, require clients is checked and send beacons at 1Mbps is unchecked. Is this normal to see the RX rate so low?

 

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 5113

Replies: 3

Related Articles
Form auth data
2394 0
DHCP Server Settings
173 0
Controller inverting input and oputput data on Radius interim updates?
993 0
Controller Migration - Usage Data and Client custom names are lost
126 0
 Will Omada capture any data?
139 0
After upgrade of Omada Software Controller V5.7 to V5.8.4 Windows no data is shown (using port 443)
1595 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.