Home

Forums

Stories

Knowledge Base

Business Community > Controllers > Hardware controller - Firmware upgrade - Can't control my AP's anymore

< Controllers

Hardware controller - Firmware upgrade - Can't control my AP's anymore

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Hardware controller - Firmware upgrade - Can't control my AP's anymore

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

bp1000

2020-10-15 13:24:42 - last edited 2020-10-19 08:36:49

Posts: 21

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2020-02-04

Hardware controller - Firmware upgrade - Can't control my AP's anymore

2020-10-15 13:24:42 - last edited 2020-10-19 08:36:49

Model: OC200

Hardware Version: V4

Firmware Version: 1.7.0 Build 20200703 Rel.59609

Just updated the OC200 to the new v1.7 firmware

Before doing so, it warned me to check compatibility, which i did.

I have 3x EAP245 and 1x EAP225-Outdoor. It wanted firmware version:

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

I checked this and have:

v2.4 on the EAP245's

v1.7 on the EAP225

So, thinking i'm all good, i go and upgrade as it kept bugging me. Now the upgrade is complete its telling me none of my devices are compatible and i cant see any clients connected to them, although the wifi AP's are still working and routing.

I did take a backup of my old controller settings, can't figure out where to restore this to.

So are my AP's not compatible with this new firmware ?

Need to get my controller back working.

Thanks!

1 Accepted Solution

Fae

2020-10-16 06:20:25 - last edited 2020-10-19 08:36:49

Posts: 3613

Helpful: 1357

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:Hardware controller - Firmware upgrade - Can't control my AP's anymore-Solution

2020-10-16 06:20:25 - last edited 2020-10-19 08:36:49

Dear @bp1000,

I have 3x EAP245 and 1x EAP225-Outdoor. It wanted firmware version:

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

I checked this and have:

v2.4 on the EAP245's

v1.7 on the EAP225

So, thinking i'm all good, i go and upgrade as it kept bugging me. Now the upgrade is complete its telling me none of my devices are compatible and i cant see any clients connected to them, although the wifi AP's are still working and routing.

The current firmware you have is apparently not the firmware it wants.

Please download the correct firmware from your region's official website:

https://www.tp-link.com/support/download/eap245/v3/#Firmware

https://www.tp-link.com/support/download/eap225-outdoor/#Firmware

Then update from the controller:

click on the incompatible EAP device to show the menu on the right side, locate to Manage Device where you can upload the firmware.

It's highly recommended to read the Omada Upgrade Guide for detailed steps,

https://www.tp-link.com/omada-sdn/controller-upgrade/#content-5_1_1

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

4 Reply

R1D2

LV6

2020-10-15 18:09:08 - last edited 2020-10-16 06:23:00

Posts: 4334

Helpful: 1039

Solutions: 173

Stories: 3

Registered: 2015-12-05

Re:Hardware controller - Firmware upgrade - Can't control my AP's anymore

2020-10-15 18:09:08 - last edited 2020-10-16 06:23:00

bp1000,

please see the FAQ of Omada SDN solution related to upgrading and management.

And make sure to read the Omada Controller Upgrade Guide before upgrading.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻

Fae

2020-10-16 06:20:25 - last edited 2020-10-19 08:36:49

Posts: 3613

Helpful: 1357

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:Hardware controller - Firmware upgrade - Can't control my AP's anymore-Solution

2020-10-16 06:20:25 - last edited 2020-10-19 08:36:49

Dear @bp1000,

I have 3x EAP245 and 1x EAP225-Outdoor. It wanted firmware version:

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

I checked this and have:

v2.4 on the EAP245's

v1.7 on the EAP225

So, thinking i'm all good, i go and upgrade as it kept bugging me. Now the upgrade is complete its telling me none of my devices are compatible and i cant see any clients connected to them, although the wifi AP's are still working and routing.

The current firmware you have is apparently not the firmware it wants.

Please download the correct firmware from your region's official website:

https://www.tp-link.com/support/download/eap245/v3/#Firmware

https://www.tp-link.com/support/download/eap225-outdoor/#Firmware

Then update from the controller:

click on the incompatible EAP device to show the menu on the right side, locate to Manage Device where you can upload the firmware.

It's highly recommended to read the Omada Upgrade Guide for detailed steps,

https://www.tp-link.com/omada-sdn/controller-upgrade/#content-5_1_1

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Hardware controller - Firmware upgrade - Can't control my AP's anymore

Hardware controller - Firmware upgrade - Can't control my AP's anymore

Information

Voters 0

Tags