Business Community > WiFi > Eap225 and omada200 extra eap only connecting wired
< WiFi

Eap225 and omada200 extra eap only connecting wired

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Eap225 and omada200 extra eap only connecting wired

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Eap225 and omada200 extra eap only connecting wired
Eap225 and omada200 extra eap only connecting wired
2020-06-09 09:52:44 - last edited 2020-06-09 11:22:49
Model: EAP225  
Hardware Version: V3
Firmware Version: Latest

Hi

 

Recently I have setup an ac1350 eap 225 access point and an omada 200 controller. Both are wired to my lan switch and the connection showing as wired in my controller software. These work fine 

 

However, I purchased a second Eap225  access point to improve my coverage this too is wired into the same switch. I can see it showing on my switch and has an ip address on my network in the correct range. However it will only adopt in the omada software as wireless! I obviously want this to be wired to my network. I tried getting around this by turning the radio off of the first aep then resetting the second but it won't detect the second aep to adopt. Likewise if I turn the radio of the first off with the second already adopted the second aep loses all connections. 

 

Can anyone please help me get both these aeps to be as wired access points on my omada controller

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Eap225 and omada200 extra eap only connecting wired-Solution
2020-06-09 10:33:09 - last edited 2020-06-09 11:22:49

@Mattyboof, turn of Mesh in Omada controller. This will probably reveal a bad wired connection between EAP 2 and your switch (cable?).

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
Recommended Solution
  1  
  1  
#2
Options
5 Reply
Re:Eap225 and omada200 extra eap only connecting wired-Solution
2020-06-09 10:33:09 - last edited 2020-06-09 11:22:49

@Mattyboof, turn of Mesh in Omada controller. This will probably reveal a bad wired connection between EAP 2 and your switch (cable?).

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
Recommended Solution
  1  
  1  
#2
Options
Re:Eap225 and omada200 extra eap only connecting wired
2020-06-09 10:39:57 - last edited 2020-06-09 11:12:15

@R1D2 

 

I did try this yesterday but did it again just now to be sure. 

 

It shows as "disconnected" in the omada software however it still shows as being on my network when I list macs and ips on my router (edgerouter). 

Edit.... 

Mate you were 100% correct tested all the cables serving the eap and one of them had a faulty orange / white. Fixed now though. 

 

Should I turn mesh back on now? 

 

 

  0  
  0  
#3
Options
Re:Eap225 and omada200 extra eap only connecting wired
2020-06-09 11:30:07

 

Mattyboof wrote

Should I turn mesh back on now?

 

If you don't plan to use a mesh network, you can disable it permanently. I always disable it by default unless the customer requires meshing.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  1  
  1  
#4
Options
Re:Eap225 and omada200 extra eap only connecting wired
2020-06-09 11:56:55
Thank you, appreciate you taking the time. I'm very new to this home networking it was a lockdown project that has taken far too much time and money to implement. Just so I understand, mesh is when the devices are connected together but for my clients in my setup, the "fast roaming" achieves the same thing? Basically all I want is that my devices/clients connect to the best eap signal as we move around the house.
  0  
  0  
#5
Options
Re:Eap225 and omada200 extra eap only connecting wired
2020-06-09 12:10:09 - last edited 2020-06-09 12:12:55

@Mattyboof, meshing is a technique to wirelessly link EAPs to the network. A mesh network is not required to use fast roaming.

 

Fast roaming just requires that the client supports the 802.11k/v standards used by Omada EAPs for fast roaming and that the Omada controller is running all the time. Of course, wireless parameters of all EAPs need to be the same for any type of roaming (basic/fast).

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  1  
  1  
#6
Options

Information

Helpful: 0

Views: 1339

Replies: 5

Related Articles
eap 225 v3 connecting issue and not showing channels in omada controller
2297 0
 Omada EAP 225 connecting to farthest AP
194 0
EAP 225 - Backdored by the update ?
549 0
EAP 225 V3 new firmware?
3469 0
 EAP 225
238 0
EAP225 not connecting to the internet intermittently
775 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.