TL-ER6020- NAT-Virtual Servers are running but go down when WAN2 links up
Hi.
NAT Virtual Server are configured to route a port via WAN1 to the LAN. It's working: access from internet alowed.
But when links up WAN2, no way to access from internet to the this port. To any port.
Checked conexion in both WANs and running.
Also checked routing this port via WAN1+WAN2 to the IP in the LAN. No way.
Must we configure something else?
Thanks in advance.
Regards.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
For tp-link router, I remember need choose interface in virtual server function, if you choose WAN1, you only are able to access internal server via WAN1.
As you said, you have built two virtual server entries?
- Copy Link
- Report Inappropriate Content
This is my config. When only WAN1 linked up there is no problem. When links up WAN2 this config don't works.
ID | Name | Interface | External Port | Internal Port | Internal Server IP | Protocol | Status | Operation |
---|
1 | proxium | WAN1,WAN2 | 57772 | 57772 | 192.168.0.3 | ALL | Enabled | ||
2 | rdjesus | WAN1,WAN2 | 16645 | 3389 | 192.168.0.2 | ALL | Enabled | ||
3 | grabadorPLV | WAN1,WAN2 | 10010 | 80 | 192.168.0.100 | ALL | Enabled | ||
4 | grabadorOLIVERAL | WAN1,WAN2 | 10009 | 80 | 192.168.0.90 | ALL | Enabled | ||
5 | grabadorOLIVERALx | WAN1,WAN2 | 37778 | 37777 | 192.168.0.90 | ALL | Enabled | ||
6 | grabadorPLVx | WAN1,WAN2 | 37777 | 37777 | 192.168.0.100 | ALL | Enabled | ||
7 | rdserver2 | WAN1,WAN2 | 10005 | 3389 | 192.168.0.5 | ALL | Enabled | ||
8 | alarmOLIVERAL | WAN1,WAN2 | 3061 | 3061 | 192.168.0.201 | ALL | Enabled | ||
9 | rdbackup | WAN1,WAN2 | 10006 | 3389 | 192.168.0.4 | ALL | Enabled | ||
10 | rdserver | WAN1,WAN2 | 10004 | 3389 | 192.168.0.3 | ALL | Enabled | ||
11 | webserver | WAN1 | 10003 | 80 | 192.168.0.3 | ALL | Enabled |
- Copy Link
- Report Inappropriate Content
You have many different servers in your LAN,
Every server all cannot work when you use WAN2?
I have doubt about you testing method, you said when you enable WAN2, you cannot access the server.
In this situation, which destinaton IP address you are using? IP address of WAN1 or IP address of WAN2?
Did you configure load balance function in this router?
If you have configured load balance function, you need tick "Enable Application Optimized Routing"
You can use telnet command to test if the specific port has opened, for example.
You can type telnet ip address of WAN1 57772, test if the 57772 be opened.
You can disable WAN1 port also, to test if there are something wrong with you WAN2 Line.
- Copy Link
- Report Inappropriate Content
I hate electronics and computers.
Now, unrasonability works.
Thanks a lot for your help.
Wish you a wonderfull year!!
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1751
Replies: 4
Voters 0
No one has voted for it yet.