Archer MR600(EU) V1 - BETA Firmware - Allowing selection of 4G+bands for Archer MR600 manually
Hi all,
Following the long thread on the same subject discssing the BETA FW, as I said I would, TPLink have given me permission to share the FW download llink.
From TPLink - We recently released a beta firmware for Archer MR600(EU) V1 which can allow us to select 4G+bands for Archer MR600 manually.
https://static.tp-link.com/2020/202004/20200420/Archer_MR600v1_1.1.0_0.9.1_[200417-rel75138]_up_boot_2020-04-20_08.44.31.zip
For Archer MR600, if you want to use its 4G+network, your SIM card should support the CA bands group Archer MR400 supports. Please check the attached picture and check if your SIM card supports the band groups on the list or not.
They asked me to state that, this BETA FW is for the Archer MR600(EU) V1 ONLY!
Neither TPLink nor me take any respnsbility if you flash a none-EU router.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@mallipoo I have tried changing the bands just like the way you described. But, CA doesn't happen. Is it possible that the tower doesn't support 4G+?
- Copy Link
- Report Inappropriate Content
@AP_Techie Pls try and see if you are getting any signal of band 40 alone. means, leave band b empty and band a with 40. If you have signals then you should have CA. else no.
- Copy Link
- Report Inappropriate Content
@AP_Techie there are still some towers where Airtel has not implemented CA yet. The LTE Category in this router doesn't support 2x2 MIMO. but you can achieve spatial diversity by mounting two LPDAs on horizontally . Or may be in different poles parallel to the ground. LPDAs never work better when they are not parallel to the ground when you are at certain distance to the mast. These LPDAs won't give you a better SINR . I already tried these. Mount these lpda horizontally and Keep enough space between them to achieve space diversity for a good gain. (This could increase your SINR). Or point at different towers, Avoid antennas to couple and give distance between them for achieving isolation. I doubt this router has Snapdragon X12. But I believe it is having a X7 which doesn't support downlink MIMO.
Hope it helps.
AP_Techie wrote
My LPDA antennas were delivered a few days ago. But I was out of station, so did not set them up yet. I'm trying to setup the antennas now. I'm looking for your expert advise on how to mount and measure the improvements. Hope you can give some guidance.
I'm located in a rural area and the nearest airtel tower is located <1Km with a clear line of sight from the terrace. Both jio and Airtel towers are located in the same area. On net monster and other apps, I've observed that Airtel signals come from 3 different towers. Two other towers are located in different directions, and they are 5-6 kms away. I've not observed 4g+ when connected to the nearest tower. Nearest tower is almost always connected on band-3(1800) and the average speeds from the terrace are 30 Mbps DL and 25 Mbps UL. This is my current setup.
I've setup the 12dbi LPDA antennas today. After connecting them to the router I've observed improvement in rsrp, but rsrq and SNR have gone down. I've gotten 10 mtr lmr400 cables ( thought I don't need 10 mtrs really) to connect the antennas to router. My suspicion is the mounting of antennas is incorrect. I haven't gotten the 90 degree perfectly, I'm going to retry this tomorrow.
My queries are about the antenna setup. Which portion of the antenna should face the tower? In my current setup, xyz area is facing the tower. Is this the right way to arrange the antenna.
Another question is, shall I mount the antennas on the same pole or two different poles? If I've to mount them on different poles, what should be the right way to setup each antenna?
Your guidance is highly appreciated. Thank you.
I've attached the signal strength values in the current setup.
- Copy Link
- Report Inappropriate Content
@mallipoo Hi, in my case I would be interested in having B1+B3. Each band alone is getting a signal but selecting both bands in the beta firmware does not lead to CA. When doing this, B3 is always selected alone. However CA works fine if I use B3+B20. By the way, the latest official firmware works just as well as the beta for me in terms of CA as it always selects B3+B20. I thought I could achieve higher speeds by using B1+B3 in the beta firmware but this combination is not supported for CA, although each one of these 2 bands get a proper signal when used alone.
- Copy Link
- Report Inappropriate Content
@mallipoo I see the signal for Band40. but rsrp, and rsrq are much worse than the B3's. So, my guess is that the B40 signal is coming from a different faraway tower.
- Copy Link
- Report Inappropriate Content
@Abhi093 I am going to try different poles today. In preparation for that, I've unscrewed the lower height antenna and verified the signal quality. Signal strength went to 100%(earlier 75% only) and SNR improved as well. So, I wonder whether we really need two antennas.
I'll post the results after mounting the LPDA antennas horizontally on two poles.
- Copy Link
- Report Inappropriate Content
Pls check my earlier post . This device doesn't support MIMO in LTE Downlink. You can get space diversity and good gain from two antennas place at some distance to avoid coupling.
- Copy Link
- Report Inappropriate Content
@AP_Techie But your speed will drop. In MIMO mode speed is better. In normal vertical mode, SNR improves, which does not give us benefit. End of day, we need speed...
- Copy Link
- Report Inappropriate Content
@mallipoo I have tried seperate vertical positioning with a distance of 3 meters. Parameters improve. But you get good speed when you tilt LPDA's by 45deg. Keeping them tilted with a space of about 3-4 feet betters SNR and RSRQ.Having tried all methods, now I use them in 45 deg polarization only.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 13
Views: 195003
Replies: 511