Business Community > WiFi > EAP110 - splitting the 2.4 and 5 Ghz services
< WiFi

EAP110 - splitting the 2.4 and 5 Ghz services

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP110 - splitting the 2.4 and 5 Ghz services

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP110 - splitting the 2.4 and 5 Ghz services
EAP110 - splitting the 2.4 and 5 Ghz services
2020-08-11 18:12:50 - last edited 2020-08-17 01:20:06
Model: EAP110  
Hardware Version:
Firmware Version:

Is there a tech document or a step by step instruction on how to split the two frequencies supported by the EAP 110 into separate services? I have so far just renamed the 5Ghz service by adding an "H" after the name, and then set the same password as the 2.4 Ghz service. However, the 5Ghz service is not visible to any devices scanning for WiFi connections.  The same method worked fine on my home router so I'm wondering if the EAP110 needs a further step somewhere?

Can anyone shed some light?

 

Thanks

EdT

  0      
 
  0      
 
#1
Options
6 Reply
Re:EAP110 - splitting the 2.4 and 5 Ghz services
2020-08-11 21:46:55 - last edited 2020-08-17 01:20:06
That model only supports 2.4 Ghz
  0  
  0  
#2
Options
Re:EAP115 - splitting the 2.4 and 5 Ghz services
2020-08-12 16:32:40 - last edited 2020-08-17 01:20:06

@pixkreen  - apologies, mental blitz. The correct model number is EAP-115

  0  
  0  
#3
Options
Re:EAP110 - splitting the 2.4 and 5 Ghz services
2020-08-19 06:00:16

@pixkreen  Apologies, the correct model is EAP115

 

  0  
  0  
#4
Options
Re:EAP115 - splitting the 2.4 and 5 Ghz services
2020-08-19 07:16:47

@EdT, EAP115 is a single-band 2.4 GHz access point, too.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#5
Options
Re:EAP115 - splitting the 2.4 and 5 Ghz services
2020-08-19 11:53:07

@R1D2 The Omada software would suggest otherwise. Below is a screenshot of the EAP115 on my network. What puzzles me is that the EAP115 shows both 2.4Ghz and 5Ghz enabled. Is this just badly written software?

  0  
  0  
#6
Options
Re:EAP115 - splitting the 2.4 and 5 Ghz services
2020-08-19 12:28:51 - last edited 2020-08-19 12:35:36

@EdT, click on »Access Points«, click on the EAP115, select tab »Configuration« and section »Radio«. This shows you what EAP115 provides.

 

The above screenshot shows what frequency bands the defined »Wireless Network« should use (as the header of the page clearly states).

Of course any wireless network can use the 5 GHz frequency band only on EAPs which support 5 GHz.

 

The ultimate source for features an EAP supports are the specifications. Here are the specifications for EAP115.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  1  
  1  
#7
Options

Information

Helpful: 0

Views: 1404

Replies: 6

Related Articles
 40Mbps on eap225 2.4 or 5 ghz
1258 0
 EAP245: 2.4 GHz does not give IP while 5 GHz does
1377 0
 EAP330 - Spread Clients evenly over 2.4 and 5 Ghz.
1068 0
Should I use the same SSID for my 2.4 and 5?
3222 0
WDS EAP110
1114 0
Is Smart Connect (one combined SSID for both 2.4 + 5 GHz) a planned feature update?
5989 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.